31
undo ipv6 dhcp server
Default
The server does not support desired address/prefix assignment or rapid address/prefix assignment.
The server preference is set to 0.
Views
Interface view
Predefined user roles
network-admin
Parameters
allow-hint
: Enables desired address/prefix assignment.
preference
preference-value
: Specifies the server preference in Advertise messages, in
the range of 0 to 255. The default value is 0. A greater value represents a higher preference.
rapid-commit
: Enables rapid address/prefix assignment involving two messages.
Usage guidelines
The
allow-hint
keyword enables the server to assign the desired address or prefix to the
requesting client. If the desired address or prefix is not included in any global address pool, or is
already assigned to another client, the server assigns the client a free address or a prefix. If the
allow-hint
keyword is not specified, the server ignores the desired address or prefix, and selects
an address or prefix from a global address pool.
If you use the
ipv6 dhcp server
and
ipv6 dhcp server apply pool
commands on the
same interface, the
ipv6 dhcp server apply pool
command takes effect.
Examples
# Configure global address assignment on the interface VLAN-interface 2. Use the desired
address/prefix assignment and rapid address/prefix assignment, and set the server preference to the
highest 255.
<Sysname> system-view
[Sysname] interface vlan-interface 2
[Sysname-Vlan-interface2] ipv6 dhcp server allow-hint preference 255 rapid-commit
Related commands
display ipv6 dhcp server
ipv6 dhcp select
ipv6 dhcp server apply pool
Use
ipv6 dhcp server apply pool
to apply a DHCPv6 address pool to an interface.
Use
undo ipv6 dhcp server apply pool
to restore the default.
Syntax
ipv6 dhcp server apply
pool
pool-name
[
allow-hint
|
preference
preference-value
|
rapid-commit
]
*
undo ipv6 dhcp server apply pool
Default
No DHCPv6 address pool is applied to an interface.
Summary of Contents for SOHO IE4300
