H3C SecPath V100-E Installation Manual Download Page 41

Page: 41 / 71

6-1

Maintaining Hardware

Preparing Tools

Phillips screwdrivers

Flat-blade screwdrivers

ESD-preventive wrist straps

Antistatic bags

None of the above installation tools are shipped with the device.

Opening the Chassis Cover

Follow these steps to open the chassis cover of the V100-E:

Step1

Power off the device and unplug the power cord.

Step2

Unplug all interface cables from the front panel while keeping the ground cable connected.

Step3

Put the device on a table with the rear panel facing you. Remove all the fastening screws on the rear
panel and both sides of the device with a Phillips screwdriver.

Step4

Lift the front of the cover to separate the front part from the chassis bottom.

Step5

Draw the cover toward you to separate the cover from the front panel and then put the removed cover
away.

Figure 6-1 shows how to open the chassis cover.

Figure 6-1

Open the chassis cover

(1)

(2)

(1) Remove six screws from these places

(2) Pull the cover out

Summary of Contents for SecPath V100-E








































































Search results

Summary of Contents for SecPath V100-E

Reviews:

Brands by name

Popular brands

H3C SecPath V100-E, Installation Manual

Search results

Summary of Contents for SecPath V100-E

Reviews:

Brands by name

Popular brands