background image

Copyright © 2017-2019, New H3C Technologies Co., Ltd. 
and its licensors 

 

All rights reserved 

No part of this manual may be reproduced or transmitted in any form 
or by any means without prior written consent of New H3C 
Technologies Co., Ltd. 

Trademarks 

Except for the trademarks of New H3C Technologies Co., Ltd., any 
trademarks that may be mentioned in this document are the property 
of their respective owners. 

Notice 

The information in this document is subject to change without notice. 
All contents in this document, including statements, information, and 
recommendations, are believed to be accurate, but they are 
presented without warranty of any kind, express or implied. H3C shall 
not be liable for technical or editorial errors or omissions contained 
herein. 

Environmental protection 

This product has been designed to comply with the environmental 
protection requirements. The storage, use, and disposal of this 
product must meet the applicable national laws and regulations. 

Documentation feedback 

You can e-mail your comments about product documentation to 
[email protected].  

We appreciate your comments 

Summary of Contents for PSR3000-54AHD


















Reviews: