H3C HIM-16GBP Interface Manual Download Page 87

Page: 87 / 102

NOTE:

In the compatibility matrixes, "

√" means "Supported" and "×" means "Not supported."

NOTE:

•

Do not install the FIP-680 in slot 5 on an SR6608/SR6608-DS router or slot 9 on an

SR6616/SR6616-DS router if the router is installed with the RPE-X5 or RPE-X5E MPU.

•

Do not install the FIP-240 in slot 5 on an SR6608 router, slot 9 on an SR6616 router, or on an

SR6608-DS/SR6616-DS router if the router is installed with the RPE-X5 or RPE-X5E MPU.

LPU and MPU compatibility matrix

Table 99 LPU and MPU compatibility matrix

LPU

RPE-X3

RSE-X3

RPE-X5

RPE-X5E

FIP-20

FIP-240

√

FIP-260

√

FIP-300

√

FIP-310

√

FIP-380

√

FIP-600

√

FIP-660

√

FIP-680

√

SAP-4E
XP

√

SAP-20
GE2XP

√

SAP-28
GE

√

SAP-XP
4GE32

√

NOTE:

In the compatibility matrixes, "

√" means "Supported" and "×" means "Not supported."

MPU and router compatibility matrix

Table 100 MPU and router compatibility matrix

Router model

RPE-X3

RSE-X3

RPE-X5

SR6604

√

SR6608

√

SR6608-DS

√

Summary of Contents for HIM-16GBP







































































































Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands

H3C HIM-16GBP, Interface Manual

Search results

Summary of Contents for HIM-16GBP

Reviews:

Related manuals for HIM-16GBP

Brands by name

Popular brands