H3C DSIC-9FSW Manual Download Page 85 | Manualshive

Page: 85 / 219

background image

76

Interface specifications

Table 103 Interface specifications

Item Description

Connector RJ-11

Number of connectors

1

Interface standard

ITU-T G991.2
ITU-T G994.1 handshaking

Interface rate

In single-pair mode, supports the sending and receiving independent
symmetric rates in the range from 192 kbps to 2312 kbps in steps of 8
kbps.
In dual-pair mode, supports the sending/receiving independent
symmetric rates in the range from 384 kbps to 4624 kbps in steps of 16
kbps.

Interface cable

Tailor-made 4-wire telephone cable

Supported services

G.SHDSL access over ordinary telephone lines

Interface LEDs

Figure 82 MIM-1SHL-4W panel

Table 104 LED description

LED Description

LINK

•

Off: No link is present.

•

On: A link is present.

ACT

•

Off: No data is being transmitted or received.

•

Flashing: Data is being received or transmitted.

Interface cables and the connection methods

For more information about G.SHDSL interface cables and the connection methods, see "

MIM-1G.SHDSL

Introduction

The 1-port Single-Pair High-Speed Digital Subscriber Line module (MIM-1G.SHDSL) adopts the
Trellis Coded Pulse Amplitude Modulation (TCPAM) approach and can provide the symmetric speed
as high as 2.3 Mbps. Its transmission speed can automatically adapt to cable length and conditions.
Compared with ADSL, G.SHDSL allows longer transmission distance and as such, can serve a wider
range of applications. It can substitute for E1/T1 lines to provide high-speed data service access.

«
...
83
84
85
86
87
...
»

Summary of Contents for DSIC-9FSW




























































































































































































































Reviews:

No comments

Related manuals for DSIC-9FSW

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 168

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 29

Brand: Panasonic Pages: 37

Brand: Panasonic Pages: 9

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

Brand: Samsung Pages: 32

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: ECKELMANN Pages: 178

Brand: Febco Pages: 12

Brand: HANYOUNG NUX Pages: 36

Brand: HANYOUNG NUX Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands