H3C DSIC-9FSW Manual Download Page 74 | Manualshive

Page: 74 / 219

background image

65

Item MIM-1CPOS(E)/MIM-1CPOS(T)

Interface standard

SONET OC-3/SDH STM-1

Interface rate

155.52 Mbps

IMPORTANT:

If the interface receives signal over a long-haul optical fiber, make sure the transmission distance is
longer than 25 km (15.53 miles). If the transmission distance is shorter than 25 km (15.53 miles), use
an optical attenuator to reduce the optical power.

Interface LEDs

Figure 69 MIM-1CPOS(E) front panel

Figure 70 MIM-1CPOS(T) front panel

Table 90 LED description

LED Description

LINK

•

Off: No link is present.

•

On: A link is present.

ACT

•

Off: No data is being transmitted or received.

•

Flashing: Data is being received or transmitted.

Transceiver modules, optical fibers, and connection methods

For more information about transceiver modules, optical fibers, and the connection methods, see
"

E1/T1 interface module

•

MIM-1E1

•

MIM-2E1

•

MIM-4E1

•

MIM-1E1-F

•

MIM-2E1-F

•

MIM-4E1-F

•

MIM-8E1

«
...
72
73
74
75
76
...
»

Summary of Contents for DSIC-9FSW




























































































































































































































Reviews:

No comments

Related manuals for DSIC-9FSW

Brand: Ransburg Pages: 49

Brand: Balboa Pages: 2

Brand: Badger Meter Pages: 20

Brand: Tapeswitch Pages: 13

Brand: Salda Pages: 20

Brand: Sanhua Pages: 3

Brand: Lab.gruppen Pages: 2

Smart Control Panel 880RGD

Brand: Raynor Pages: 4

Brand: Technische Alternative Pages: 68

Brand: Sherlotronics Pages: 2

WFHC 06Z 02 HC RF 24

Brand: Watts Pages: 18

Brand: Waters Pages: 39

DHI-IPMECD-3021 Series

Brand: Dahua Technology Pages: 28

Brand: Carel Pages: 2

SYNCHRO QUASAR AC

Brand: UCS Pages: 10

MultiMode 1214-8

Brand: Curtis Pages: 41

Brand: Jetter Pages: 62

Brand: CALEFFI Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands