manualshive.com logo in svg

H2X THERAPOOL D, Owner'S Manual, Page: 86 / 108

Share
Download
H2X THERAPOOL D Owner'S Manual Download Page 86

84

DO NOT DIVE.

109

DO NOT DIVE.

MEMORY FAILURE - CHECKSUM ERROR*

At power up, the system has failed the Program Checksum Test. This indicates a problem with the 
firmware (operation program) and requires a service call.

MEMORY WARNING - PERSISTENT MEMORY RESET*

Appears after any system setup change. Contact your dealer or service organization if this message 
appears on more than one power up, or if it appears after the system has been running normally 
for a period of time.

MEMORY FAILURE - CLOCK ERROR*

Contact your dealer or service organization.

CONFIGURATION ERROR – SWIM SPA WILL NOT START UP

Contact your dealer or service organization.

A PUMP APPEARS TO BE STUCK ON

Water may be overheated. POWER DOWN THE Swim spa. DO NOT ENTER THE WATER. Contact 
your dealer or service organization.

A PUMP APPEARS TO HAVE BEEN STUCK ON WHEN SWIM SPA WAS 
LAST POWERED

POWER DOWN THE Swim spa. DO NOT ENTER THE WATER. Contact your dealer or service organi-
zation.

* This message can be reset from the topside panel with any button press.

Swim spa Controls

System Related Messages

Summary of Contents for THERAPOOL D













































































































Reviews:

No comments