background image

Re-check the center of gravity, move the battery position if necessary so that it balances in a very 

slight nose down attitude somewhere near the forward mark (55mm). Check that the linkages and 

pushrods are secure, the propeller is secure and the wings are correctly attached. 

Switch on the transmitter with the throttle closed and the throttle trim fully down then connect the 

flight battery. Check that all the controls are working freely, no binding and that they are working in 

the correct sense, ie, aileron stick left (left aileron goes up), elevator stick back (elevator goes up), 

rudder stick left (rudder goes left). To arm the stabilization system you need to open the throttle to a 

low setting for 7 or 2 seconds then close the throttle. Now pick the model up and check to see if it is in 

beginners mode or advanced mode. To do this move the nose up and down with the battery hatch off 

and watch the elevator servo movement. If it's in beginners mode the servo will move quite a bit, in 

advanced mode the servo will move less. Set the stabilization system into beginners mode then check 

that it is working correctly by doing the following test. Roll the aircraft to the right, the left aileron 

should go up and the right down. Roll the aircraft to the left and the right aileron should go up and 

the left down. Move the nose down and the elevator should go up, move the nose up and the 

elevator should go down. Move the nose of the aircraft to the left and the rudder should move right, 

move the nose right and the rudder should go left. If all works correctly then you are ready to fly. 

So for which ever level of skill you are select the appropriate flight mode. Place the aircraft on your 

take off area pointing into wind. It is best to use either a tarmac area or an area with very short grass, 

long grass could cause it to nose over. Re-check the controls are working correctly then hold in some 

up elevator, gently open up the throttle and correct any swing using the rudder, with a clockwise 

rotating propeller the tendency will be to swing right so some left rudder may be needed. As the 

model accelerates ease off some of the up elevator so that the tail rises and the model is running on 

its main wheels slightly nose up. When full power is reached the Skyraider will take off very smoothly, 

climb out gently, do not try and climb too steeply, the whole time keep it pointing into wind, do not 

allow it to turn (in beginners mode the stabilizer will help keep the model flying straight). Climb up to 

a safe height then throttle back to about half or just over. When at a safe height and upwind you can 

practice some gentle turns left and right, do not try and turn too steeply at first if you are 

inexperienced. 

If 

things start to go wrong, close the throttle a bit more and centralise the ailerons and 

elevator, the stabilizer will then fly the model for you in a steady straight line. Once you have 

regained your composure gently turn the model back to overhead the take off area. 

Once you have settled down and are happy doing very gently turns then it is time to think about 

landing. Try and fly a nice circuit around the landing strip at about 700ft so that you end up slightly 

downwind of the landing area pointing into wind. Gently close the throttle to a point where the 

model is descending nicely, not too steeply and keep the wings level (the stabilizer will be helping you 

with this). When the model is about 5ft from the ground close the throttle completely, at about 2ft 

from the ground apply a small amount of up elevator and just hold it there and the model will 

gently flare and land. If all is well and as the model slows on the ground feed in full up elevator to 

keep the tailwheel on the ground. To taxy back keep full up elevator in and gently use the throttle and 

the rudder to steer the model back. 

We hope you enjoy flying your H-KING A-7 Skyraider and if you haven't already tried out the others in 

our range then we recommend you visit our website at  www.hobbyking.com and take a look at our 

ever increasing range of quality model aircraft and  accessories. 

10 

Summary of Contents for A-1 SKY RAIDER















Reviews: