GYMFORM SLIM FOLD TREADMILL, Instruction Manual

Page: 7 / 36

7
it should be replaced with a
special cable available from the
manufacturer or technical service.
- Do not use the device if you
weigh more than 110 kg.
- This device is designed for
individual use. Any breakdown
caused by improper use is not
covered by the warranty.
- Make sure the device is on a
flat surface. Do not use dangling
clothing on the treadmill and do
not scuff the treadmill, as this will
make it difficult to use. Wear sport
shoes when using the treadmill.
Do not start the treadmill while
standing on it. The best position
when turning on the device is to
stand with one foot on either side
of the treadmill. If the initial speed
of the treadmill is too fast, do not
jump on the treadmill. Start using
it at a lower speed and increase it
gradually.
- Do not suddenly stop walking or
running on the treadmill. Press the
ON/OFF button and the treadmill
will gradually stop.
- Stop walking when the treadmill
stops.
- Leave a safety area of 2 metres
by 1 metre behind the treadmill.
PRECAUTION: DO NOT remove
the cover of the control panel,
as this may cause an electric
shock. The parts inside cannot
be repaired by the user.
Product description
1. Control panel
2. Emergency key
3. Base
4. Treadmill
5. Vertical bar screw
6. Handlebars
7. Lock screw
8. Control panel screw
9. ON/OFF button
10. MODE button
11.
button
12. ↓ button
13. ↑ button
14. Function indicators
15. Small Allen key
16. Large Allen key
17. Vertical bars
18. Metal base
19. Base extension
20. Washers x 6
21. Screws x 6
22. Handlebar cable
23. Vertical bar cable
24. Screws x 2
25. Nuts x 2
26. Handlebar screws
27. Spanner
28. Pulse sensors
29. Belt screws
30. Wheels
Assembly Instructions
1. Open the box, unpack all the parts and take
out the treadmill.
INSTALLING THE METAL BASE (See Picture
6)
2. Place the treadmill in the upright position on a
flat surface.
3. Make sure that the screw on the vertical bar
(5) is in place and is attaching the base (3) to
the vertical bar (17).
4. Attach the base extension (19) to the metal
base (18) with six washers (20) and six screws
(21) and the large Allen key (16).
INSTALLING THE HANDLEBARS (See Picture
7)
5. Remove the screw on the vertical bar (5) that
is connecting the base (3) to the vertical bar
(17).
6. Gradually lower the base (3) until it is resting
on the floor.
7. Connect the handlebar cable (22) to the
vertical bar cable (23). See Picture 7.
8. Place the handlebars (6) on top of the vertical
bars (17) and attach them with two screws (24)
and nuts (25). Tighten them with the small Allen
key (15) and spanner (27). Ensure that they are
firmly attached.
9. Attach the handlebars with the two handlebar
screws (26).
INSTALLING THE CONTROL PANEL (See
Picture 8)
10. Lift up the control panel (1) so it is in the
right position and then fasten it with the panel
screw (8).
IMPORTANT:
11. Before using the treadmill, always make
sure that the base (3) is firmly attached to the
vertical bar (17). To do so, tighten the lock pin
(7). (See Picture 3)
Instructions for Use:
1. Connect the plug to the power supply.
2. Press the ON/OFF button (9) located on the
bottom front of the device.
3. The emergency key (2) has a clip to attach
it to clothing. Attach it to the clothing you are
wearing.
4. Attach one end of the emergency key (2) to
the control panel (1). It is a magnetic attachment.
Adjust the length of the cable from the clip to the
control panel so that it disconnects as soon as
you move too far away from the control panel.
Whenever you use the treadmill, attach the