GW Instek COM-804 User Manual Download Page 65

Page: 65 / 157

GOM-804 & GOM-805 User Manual

Ambient Temperature

Background

The Ambient Temperature setting is used to set the
ambient (room temperature) for the Temperature

Compensation or Temperature Conversion function in
the absence of the PT-100 temperature sensor. See page

52 and 56 respectively for details.

1. Select Ambient
Temperature
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display
has focus.
Go to Meas. Setup and press Enter.
Go to Ambient Temperature and

press Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

2.Ambient
Temperature
setting appears

Use the arrow keys to set the Ambient Temperature.

Press Enter to confirm the setting.

Ambient

Temperature

Ambient Temperature Off, On: -50ºC ~ 399.9ºC

Note

Pressing ESC before pressing ENTER will exit the Ambient
Temperature setting.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands