GW Instek COM-804 User Manual Download Page 52

Page: 52 / 157

MEASUREMENT

1. Select the
Temperature
Compensation
mode

Press

to access the Temperature Compensation

function.
The temperature-compensated resistance measurement
will appear on the display.

Temperature

compensation

function indicator

Ambient
temperature
source

Extrapolated resistance

measurement at the desired

(

“correct”

) temperature

Correct Temperature,

Temperature Coefficient settings

Ambient
temperature

2. Ambient
Temperature

The ambient temperature can be either measured with
the PT-100 sensor or be set manually.
If  using the PT-100 sensor the Ambient temperature
setting should be turned off. If  the PT-100 probe is not

used, then the ambient temperature needs to be manually
set.

From the bottom menu, go to Meas. Setup > Ambient

Temperature and set the ambient temperature.
See page 66 for setting details.

Range

Off, -50.0 ºC ~ 399.9ºC

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands