GW Instek COM-804 User Manual Download Page 66

Page: 66 / 157

MEASUREMENT

Line Frequency

Background

The Line Frequency setting selects the appropriate line
filter to reduce the influence of the AC line frequency on

the milliohm measurements. This setting is set to AUTO
by default.

1. Select Line
Frequency
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to Meas. Setup and press Enter.
Go to Line Frequency and press
Enter.

Meas. Setup

menu icon

Move

Select menu

or setting

Enter

2.Line Frequency
setting appears

Use the arrow keys to set the Line Frequency. Press Enter
to confirm the setting.

Line Frequency

Auto, 50Hz, 60Hz

Note

Pressing ESC before pressing ENTER will exit the Line
Frequency setting.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands