manualshive.com logo in svg

Gutermann AQUASCOPE 3, Operating Manual

Share
Download
Gutermann AQUASCOPE 3 Operating Manual Download Page 18

AQUASCOPE 3

Version 1.3

17/19

10.

Battery replacement

At the back of the amplifier is the battery compartment. Please lift the

battery  compartment  cover.  There  are  4  LR6  (AA)  size alkaline
batteries.  When  the  battery  charge  indicator  on  the  display  suggests
replacing  the  batteries,  please  make  sure  that  all  4  batteries  are
replaced at the same time. When inserting the batteries please observe
the correct direction (+ and – according to the indicated position).

11.

Technical Specifications

1.

The  control  unit  should  be  manufactured  from  a  high
strength  PVC  material  that  is  resistant  to  exposure  from
high levels of UV exposure.

2.

Power  supply  comprises  of 4  x standard  LR6”  or  “AA”
Alkaline batteries.

3.

The System has a Frequency range of 1 – 5000Hz

4.

The control unit has amplification of 60DB or more.

5.

The Sensitivity in the hand probe is 15v/g or more.

6.

The Sensitivity in the ground microphone is 20 v/g or more.

7.

The Aquascope  3  has  a  display  showing  battery  status,
noise level, volume setting and signal strength.

8.

The center  frequency  of  a  band-pass filters shown  as  a

numeric  value. The  operator  tunes  into  the  exact  filter
setting required in increments of 40Hz.

9.

Activating the filters only takes one simple button press.

10.

The filter  settings  have  a narrow  bandwidth to  allow  for
optimal acoustic tuning of the leak noise.

11.

The ground microphone to cable connector is at a height
greater  than  400mm  from  the  floor  so  it  cannot  be
accidentally kicked by the operator.

12.

The ground microphone to controller cable runs within the
ground  microphone  handle, this reduces exposure  to
increased background noise from wind.

Summary of Contents for AQUASCOPE 3





















Reviews:

No comments

Brands by name

Popular brands

Load more brands