Contents:
a. ButtKicker Gamer with Easy Clamp™ attachment mechanism
b. 100 watt ButtKicker Gamer Power Amplifier with optional standing feet
c. 13.5’ cable with quick release connecting ButtKicker Gamer to amplifier
d. RCA and mini “Y” adapters
e. 5’ RCA to RCA cable and 5’ RCA to mini cable
f. Two Velcro® cables
Thank you for purchasing
the ButtKicker Gamer.
This guide will help you to quickly set up your new ButtKicker system
with your PC or gaming console.
ButtKicker® Gamer
BK-GR
CONSOLE GAMING
START HERE
Position the strain relief rubber band
on the ButtKicker Gamer cable
1.
Position the rubber strain relief on the ButtKicker® Gamer
cable until it is approx. 6” away from the ButtKicker Gamer.
2.
Pull the loop of the strain relief nearest to the ButtKicker
Gamer tight.
3.
Place the second loop about 8” further down the cable and pull
it tight. (refer to figure 1)
Attach the ButtKicker Gamer
to your center post chair
1.
Raise the pneumatic lift on your chair (make the seat of the chair
higher). Then, push down the sleeve covering the center post to
expose the post. (refer to figure 2)
2.
Loosen the knob on the arm of the ButtKicker Gamer and place
the clamp around the post.
3.
Tighten the knob and secure the ButtKicker Gamer in place on
the chair seat. (refer to figure 2)
4.
Use the supplied Velcro® cable wraps to tie the end of the
ButtKicker Gamer cable to one leg of your seat. (refer to figure 3)
Position the Gamer Amplifier and
connect to the ButtKicker Gamer
Do not turn on the Gamer Amplifier until
all of the connections are made!
1.
Connect the longer cable that attaches to the Gamer Amplifier to
the shorter cable coming from the ButtKicker Gamer. (refer to
large diagram &
figure 3b
) [Note that the cables may be
disconnected using the quick release connector at any time if
desired.
HOWEVER
, make sure the amplifier is turned off
BEFORE
disconnecting the cables.]
2.
Position the amplifier near the audio source (gaming console),
and accessible to the user.
3.
If desired, use the optional standing feet to position the amplifier
in an upright position. Attach one foot to the amplifier case by
gently bending down on the ends of the foot so that the middle
channel of the foot will fit snuggly over the edge of one of the
bolts on the amplifier case. Repeat this step with the other foot.
4.
Connect the power cord to the power terminal on the back of the
Gamer Amplifier and then plug it into a power outlet.
Connecting the audio signal from the gaming
console to the Gamer Amplifier
If the audio is hooked up using the standard R/L (red/white) audio
cables
, insert the red male RCA plug of the gaming console into the
female end of the RCA“Y” adaptor. Then plug the red male RCA end
of the RCA “Y” adaptor into your television or stereo system.
Connect the female end of the 5’ RCA to RCA cable to the black male
end of the RCA “Y” adaptor. Connect the male end of this cable to
the “line level input” RCA input on the back of the Gamer Amplifier.
For a gaming console hooked up to a separate surround sound
system,
use the RCA “Y” adaptor to split the “sub out” output of your
surround sound processor. Use the 5’ RCA to RCA cable to connect
one leg of the RCA “Y” adaptor to the “line level input” RCA input on
the back of the Gamer Amplifier, and connect the audio cable of your
subwoofer to the other leg of the RCA “Y” adaptor.
CONSOLE SYSTEM ADJUSTMENT
PLEASE NOTE:
TURN OFF THE GAMER AMPLIFIER WHEN NOT IN USE.
Figure 1
Figure 2
Figure 3
PLEASE NOTE:
THE QUICK CONNECT CABLE ONLY FITS ONE WAY.
Make sure pins are properly aligned with the large pin
in the large hole and the small pin in the small hole.
Figure 3b
b.
c.
f.
e.
d.
a.
1.
Turn on the Gamer Amplifier.
2.
Turn on your gaming console and play your favorite game
or movie.
3.
Adjust the Gamer Amplifier. See the FAQ section on the
back page for detailed information on common knob and
switch settings.
4.
If you are using your gaming console through a surround
sound receiver, you may need to adjust the level of the
subwoofer output to give more or less input signal to the
Gamer Amplifier.
5.
If your chair has levers that rattle, jam foam under the lever
or hang a bean bag on the handle.
6.
Enjoy!
All manuals and user guides at all-guides.com
all-guides.com
