Gude Expert Power Control 8042 Series Manual Download Page 23 | Manualshive

Page: 23 / 96

background image

23

Expert Power Control 8042

© 2020 GUDE Systems GmbH

Operating

3) by Software: (only if "Enable FW to BL" was previously activated in the
"GBL_Conf.exe" application)

·

Start the "GBL_Conf.exe" program

·

Do a network search with the "Search" menu action

·

Activate in menu "Program Device" the item "Enter Bootloader"

4) via web interface:

Press "Enter Bootloader Mode" on the maintenance

web page.

Whether the device is in Bootloader mode, is indicated by the flashing of the status
LED, or it is shown in "GBL_Conf.exe" application after a renewed device search (ap-
pendix "BOOT-LDR" after the device name). In Bootloader mode the program
"GBL_Conf.exe" can disable the password and the IP ACL, perform a firmware update,
and restore the factory settings.

For devices with relays, entering or exiting the bootloader mode does not change

the state of the relays as long as the operating voltage is maintained.

Abandonment of the Bootloader Mode

1) via push button:

·

Hold both buttons for 3 seconds (only if the device has 2 buttons)

2) or

·

Remove and connect the power supply without operating a button

3) by Software:

·

Start the "GBL_Conf.exe" application

·

Do a network search with the "Search" menu action

·

In menu

"

Program Device

"

activate the item "Enter Firmware"

Factory Reset

If the device is in bootloader mode, it can always be put back to its factory default. All
TCP/IP settings are reset in this operation.

If a unit is set to factory defaults, an uploaded certificate or updated firmware will

be preserved.

1) via push button:

·

Activate the Bootloader Mode of the device

·

Hold down the button (or the "Select" button for devices with 2 buttons) for 6
seconds. If the push button is recessed, use a pin or paper clip

·

The status LED will blink in a fast rhythm, please wait until the LED blinks slowly
(about 5 seconds)

2) by Software:

·

Activate the Bootloader Mode of the device

·

"Start the GBL_Conf.exe" program

·

In menu "Program Device

"

activate the item

"Reset to Fab Settings"

20

«
...
21
22
23
24
25
...
»

Summary of Contents for Expert Power Control 8042 Series

































































































Reviews:

No comments

Related manuals for Expert Power Control 8042 Series

ControlMaster CM15

Brand: ABB Pages: 28

Smart-MPPT Li Series

Brand: Y-Solar Pages: 6

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: Canarm Pages: 3

Brand: GAUGEMASTER Pages: 2

Brand: EasyIO Pages: 19

Brand: Zero 88 Pages: 2

Brand: Zenit Pages: 24

Brand: PAC Pages: 17

Brand: GARAN Pages: 8

Brand: Gamma Vacuum Pages: 25

Brand: Gamma Pages: 28

Brand: Samson Pages: 20

Brand: Eaton Pages: 8

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands