manualshive.com logo in svg

GÜDE Expert PDU Energy 8311 Series, Manual

Share
Download
GÜDE Expert PDU Energy 8311 Series Manual Download Page 16

16

Expert PDU Energy 8311 

 

                                                                                                                                                                                         © 2021 GUDE Systems GmbH

Operating

Interface GBL_Conf

To check the network settings with GBL_Conf.exe, start the program and choose 

"All

Devices"

 in the 

"Search"

 menu. From the list select the appropriate device. The lower

part of the left half of the window now shows the current network settings of the device.
If the IP address is displayed with the default settings (192.168.0.2), either no DHCP
server is present on the network, or there could be no free IP address assigned to it.

·

Activate the Bootloader Mode (see Chapter Bootloader Mode) and choose in menu

"Search" the item "Bootloader-Mode Devices only"

·

Enter the desired settings in the edit window and save them with 

"Save Config".

·

Deactivate the boot loader mode for the changes to take effect. Select again 

"All

Devices"

 in the 

"Search"

 menu of GBL_Conf.exe. 

The new network configuration is now displayed.

Factory Reset

The device can be reset to the factory default via the web interface from the Mainten-
ance Page

 or from the Bootloader mode (see chapter Bootloader activation

). All

TCP/IP settings are reset in this operation.

  If a unit is set to factory defaults, an uploaded certificate or updated firmware will

be preserved.

2.3.1

Maintenance Page

This section provides access to important functions such as Firmware Update or Re-
start Device. It is advisable to set an HTTP password for this reason.

16

19

Summary of Contents for Expert PDU Energy 8311 Series


















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands