GTO F3101MBC Manual Download Page 6

rev - 12/01/10 

2

 

Step 2:

  Remove the base unit battery cover using a small phillips head screwdriver. Install the rechargeable Ni-MH battery (included). 

Replace battery cover.

 

 

2. Connect the Transformer and Test Base 

Unit 

Step 1:

 

Find a convenient location near an AC outlet to mount or place the 

base unit. 

 

Step 2:

 

Plug the transformer into the outlet and connect it to the base unit.

 

The base unit can be disconnected from the transformer for use in another 

location. The battery will last approximately four (4) hours when 
unplugged from the transformer. 

You can turn the base unit OFF to 

conserve battery power, however it will not receive a signal.

 

Step 3:

 

Test the base unit by pressing the CALL button on the keypad. The 

base unit will ring.

 

3. Install and Test Keypad

 

You will need to hard-wire your keypad to the gate opener if you:

 

 

Do NOT have a GTO Entry Transmitter.

 

 

Have a GTO Access Systems GP Series gate opener.

 

 

Live in an area with high radio frequency interference.

 

Skip to page 5 for instructions.

 

For 

wireless

 applications, the keypad 

must

 be in line of sight of 

and

 no more than 50 ft. away from the gate opener 

receiver. Test the keypad range before permanently mounting it. 

 

Charge battery for 12 hours 
before using the system for 
the first time.

 

Summary of Contents for F3101MBC













Reviews: