GSS GLC 100 Assembly Instructions Manual Download | Manualshive

Page: 22 / 32

background image

- 22 -

GLC 100

7

C

onfiguration

s

oftware

With the Software "GSS.lan configuration" EoC modems are indicated in a
network, network names are assigned and private and secured networks are
created (128 Bit/AES Encryption).

The network name "HomePlugAV" represents a public network. The EoC mo-
dems are shipped with the "HomePlugAV" as the default network name.

With the software "GSS.lan configuration" a firmware update of the EoC
modem is possible. Thus, EOC devices can always be updated to the current
status.

In general, multiple networks can be set up in a coax distribution network.
Through the network name or network key, the modems are assigned to a
network.

7.1 i

nstall ation

• Unzip the software package after downloading from www.gss.de.

—> When installing "GSS.lan configuration" software WinPcap library

V4.1.2 is installed. Already installed other versions of the WinPcap
library must be uninstalled before.

• Start the "Setup.exe" file.

• Follow the instructions in the Setup Wizard.

—> If an older version of the software is found on your PC, first you

should uninstall it.

«
...
20
21
22
23
24
...
»

Summary of Contents for GLC 100

































Reviews:

No comments

Related manuals for GLC 100

Nighthawk R7100LG

Brand: NETGEAR Pages: 179

Brand: Planet Pages: 36

Brand: Teleorigin Pages: 35

Brand: NetComm Wireless Pages: 60

Brand: GDI Pages: 23

Brand: Zte Pages: 25

Brand: StarHub Pages: 10

Brand: RCA Pages: 112

Brand: OptConnect Pages: 17

Brand: OptConnect Pages: 24

BritePort 8012-G1

Brand: Broadxent Pages: 55

Brand: Connect One Pages: 15

Brand: NETGEAR Pages: 24

SupraExpress 56e

Brand: Diamond Pages: 102

Brand: TRENDnet Pages: 2

Brand: TRENDnet Pages: 3

Brand: Rae Pages: 42

WINCOMM V.92_LX

Brand: Jaton Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands