GSi PNEG-1393 Assembly Instructions Manual Download Page 6

2. Safety

6

PNEG-1393

 54'-60' Diameter 36-37 Rings Externally Stiffened 2 Ring Door

General Safety Statement

Our foremost concern is your safety and the safety of others associated with grain handling equipment. 
This manual is to help you understand safe operating procedures and some problems that may be 
encountered by the operator and other personnel.

As owner and/or operator, you are responsible to know what requirements, hazards, and precautions exist 
and inform all personnel associated with the equipment or in the area. Safety precautions may be required 
from the personnel. Avoid any alterations to the equipment, which may produce a very dangerous 
situation, where SERIOUS INJURY or DEATH may occur.

You should consider the location of the bin site relative to power line locations or electrical transmission 
equipment. Contact your local power company to review your installation plan or for information 
concerning required equipment clearance. Clearance of portable equipment that may be taken to the bin 
site should also be reviewed and considered. Any electrical control equipment in contact with the bin 
should be properly grounded and installed in accordance with National Electric Code provisions and other 
local or national codes. 

This product is intended for the use of grain storage only. Any other use is a misuse of the product.

Sidewall bundles or sheets must be stored in a safe manner. The safest method of storing sidewall 
bundles is laying horizontally with the arch of the sheet upward, like a dome. Sidewall sheets stored on 
edge must be secured so that they cannot fall over and cause injury. Use care when handling and moving 
sidewall bundles.

Personnel operating or working around equipment should read this manual. This manual must be 
delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse 
of the equipment.

This product has sharp edges, which may cause serious injury. To avoid injury, handle 
sharp edges with caution and always use proper protective clothing and equipment.

Summary of Contents for PNEG-1393































Reviews: