GSi 42-60 X Series Assembly Instructions Manual Download

Page: 64 / 96

4. Assembly Instructions

PNEG-1773-EU

42'-135' “X” Series Ladder, Cage and Platform - European Standard

“X” Series Ladder Intermediate Platform Package

Platform Package

1. Attach the wall angle to the sidewall sheet with 3/8" hardware. Assemble the left and right

intermediate platform brackets to the wall angles with 3/8" hardware.

(See Figure 4AM.)

NOTE: Leave all hardware loose until completely assembled.

Assemble the platform to the front and back angles and platform brackets using the 5/16" truss bolts.

Using 5/16" hardware, assemble the posts.

Figure 4AM

Ref #

Part #

Description

LDR-5168

Ladder Sidewall Angle

LDR-5183

Intermediate Platform Back Post - Left

LDR-5172

Ladder Intermediate Platform

LDR-5184

Intermediate Platform Back Post - Right

LDR-5179

Intermediate Platform Front Post (2)

LDR-5180

Intermediate Platform Toe Board

STX-0138

“X” Series Eave Platform Middle Angle (2)

LDR-5175

Intermediate Platform Front Angle

LDR-5173

Intermediate Platform Bracket - Right

LDR-5174

Intermediate Platform Bracket - Left

Use 5/16"-18 x 3/4" truss bolt (S-10267) and 5/16"-18 flange nut (S-10268) to attach platform
floor and all substructure.

Attach all handrail posts to platform using 5/16"-18 x 1" flange bolt (S-10260) and 5/16"-18
flange nut (S-10268).

Attach ladder sidewall angle to intermediate platform bracket using 3/8-16" x 1" flange bolt
(S-7485) and 3/8"-16 flange nut (S-9426).

Summary of Contents for 42-60 X Series

































































































Search results

Summary of Contents for 42-60 X Series

Reviews:

Related manuals for 42-60 X Series

Brands by name

Popular brands

GSi 42-60 X Series, Assembly Instructions Manual

Search results

Summary of Contents for 42-60 X Series

Reviews:

Related manuals for 42-60 X Series

Brands by name

Popular brands