Allgemeiner T
e
il / General Section
UMS 25
1 - 10
GRUNDIG
Service
SETTINGS
____________________________________________________________________________
Setting the time
When the stereo is connected to the mains supply and the time has not been set,
the time display flashes.
Note:
Perform the setting in switched-off state.
1
Activate time-setting function by pressing »
CLOCK TIMER
« and holding
down.
– In the display, »
ȄȄ
« flashes.
2
Press »
MEMORY
« and set the hour with »
–
«.
3
Press »
MEMORY
« and set the minute with »
–
«.
4
Confirm input with »
MEMORY
«.
Note:
The time must be reset after a power failure or when the mains plug is pulled
out.
Setting the time for 12-hour display
1
Switch on stereo system by pressing »
ǼǼ
ON
«.
2
Press »
SOURCE
« until »
TAPE
« appears in the display.
3
Activate the time-setting function by pressing »
CLOCK TIMER
«.
– In the display, for example, »
I 4 : 0 0
« appears.
4
Press »
MEMORY
« and hold down while pressing »
ı
II
«.
– »
P M
« appears briefly in the display; the time has been switched to
12-hour display.
Note:
Repeat procedure to set for 24-hour display.
1 1:20
Ȅ
15:00
Ȅ
PM 02.00
|__ |__ |__ |__ |__ |__ |__ |__
|__ |__ |__ |__ |__ |__ |__ |__
VOLUME
I
I
I
I
I
I
I
I
14:00
|__ |__ |__ |__ |__ |__ |__ |__
|__ |__ |__ |__ |__ |__ |__ |__
VOLUME
I
I
I
I
I
I
I
I
Searching for and saving radio stations –
with the automatic station search
Note:
When making this setting, no more than 5 seconds may elapse between
pressing various keys.
1
Switch on stereo system with »
TUNER /BAND
«.
2
Select desired frequency range (FM, MW or LW) with »
TUNER /BAND
«.
– In the display, »
F M 8 7 . 5 0
« may, for example appear.
3
Start the automatic station search for the FM range by keeping
»
aa
TUNE –
« or »
TUNE +
ss
« on the remote control pressed down.
– The search stops, as soon as a radio station with a sufficiently strong signal
is found.
– The frequency of the station can be tuned step-by-step (500kHz) with
»
aa
TUNE –
« or »
TUNE +
ss
« on the remote control.
4
Press »
MEMORY
« and select the desired station with »
PRESET
« or
»
1 ... 0
« on the remote control (1 to 24 in the FM range, 1 to 12 in
the MW and LW ranges).
– The selected channel position appears in the display, »
F M P R : 0 2
«, for
example, and in the case of RDS stations, the station name appears direct-
ly afterwards.
5
Save setting with »
MEMORY
«.
– In the display, the selected channel position will appear, for example
»
F M P R : 0 2
«.
6
To tune into other radio stations in the FM range, repeat procedure from
point
3
, for the ranges »
M W
« and »
L W
«, repeat from point
2
.
SETTINGS
____________________________________________________________________________________
TUNER
|__ |__ |__ |__ |__ |__ |__ |__
|__ |__ |__ |__ |__ |__ |__ |__
VOLUME
I
I
I
I
I
I
I
I
MHz
FM 87.50
|__ |__ |__ |__ |__ |__ |__ |__
|__ |__ |__ |__ |__ |__ |__ |__
VOLUME
I
I
I
I
I
I
I
I
MHz
FM PR:02
|__ |__ |__ |__ |__ |__ |__ |__
|__ |__ |__ |__ |__ |__ |__ |__
VOLUME
I
I
I
I
I
I
I
I
ST
MHz
PROG.
