GRUNDIG Service
Chassis 14.2
2 - 2
4. Geometry
– Apply a geometry test pattern.
– Start the Service Mode: press button "
i
" –> enter "
8500
".
– Call up the geometry function with buttons
P+
/
P-
and adjust the
geometry with buttons
Ǹ
/
Ƿ
:
– Vertical slope
VSLP
. The lower half part of the pattern is blanked.
Adjust picture so that the middle line of the pattern is cut.
– Zoom vertical
VZOM
.
For 16:9 sets, adjust the value to 25.
For 4:3 sets, adjust the circle of pattern just touches to the upper
an lower edges. Readjust the VSLP if required.
– Vertical shift
VSHT
.
– Vertical linearity
SCOR
.
– Vertical amplitude
VAMP
.
– Horizontal width for 4:3 sets
EWW
.
– Horizontal width for 16:9 sets
EWW1
.
Adjust
EWW
afterward:
EWW
= EWW1 –
21
– Vertical zoom for 16:9 sets
VZM1
. Adjust the vertical amplitude
so, that second lines from top and lower just touches to the edges.
– Horizontal shift
HSHT
.
– East west parabola width 4:3
EWPW
.
– East west trapezium
EWT
.
– East west parabola width 16:9
EWP1
.
– Upper corner parabola
EWCU
.
– Lower corner parabola
EWCL
.
– Vertical parallelogramm with
HPAR
.
– Vertical bow
HBOW
.
– End the Service Mode: Press button "
TXT
".
5. White Balance / Cut off
– Apply a Grey Scale Test pattern.
– Start the Service Mode: press button "
i
" –> enter "
8500
".
– Call up
GRN
with buttons
P+
/
P-
and set it to 32 with buttons
Ǹ
/
Ƿ
.
– Call up
RED
and
BLUE
with buttons
P+
/
P-
and adjust the values
so that the white part of the picture becomes achromatic. If white
balance can not be adjusted properly change GRN value.
– Call up
BLOR
and
BLOG
with the buttons
P+
/
P-
and adjust the
values so that the dark part of the picture becomes achromatic.
– End the Service Mode: Press button "
TXT
".
4. Geometrie
– Geometrie-Testbild einspeisen.
– Service Mode aufrufen: Taste "
i
" drücken –> "
8500
" eingeben.
– Mit den Tasten
P+
/
P-
die gewünsche Bildgeometrie-Abgleich-
funktion aufrufen und mit den Tasten
Ǹ
/
Ƿ
die Geometrie einstellen:
– Bildmitte vertikal
VSLP
. Die untere Bildhälfte ist ausgeblendet.
Den Bildinhalt so einstellen, dass die Mittelline gerade nicht mehr
sichtbar ist.
– Zoom vertikal
VZOM
.
Bei 16:9 Geräten den Wert auf 25 einstellen.
Bei 4:3 Geräten VZOM so einstellen, dass der Kreis gerade den
Rand berührt. Gegebenenfalls VSLP nochmals korrigieren.
– Bildposition vertikal
VSHT
.
– Bildlinearität vertikal
SCOR
.
– Bildhöhe vertikal
VAMP
.
– Bildbreite bei 4:3 Geräten
EWW
.
– Bildbreite bei 16:9 Geräten
EWW1
.
Anschließend
EWW
einstellen:
EWW
= EWW1 –
21
– Zoom vertikal bei 16:9 Geräten
VZM1
. Bildhöhe so einstellen,
dass die 2 Line von oben und von unten am Bildrand ist.
– Bildposition horizontal
HSHT
.
– Ost/West-Parabel 4:3
EWPW
.
– Ost/West-Trapez
EWT
.
– Ost/West-Parabel 16:9
EWP1
.
– Ecken oben
EWCU
.
– Ecken unten
EWCL
.
– Schräglage vertikal (Parallelogramm)
HPAR
.
– Biegung vertikal
HBOW
.
– Service Mode beenden: Taste "
TXT
" drücken.
5. Weißabgleich / Cut off
– Testbild Grautreppe einspeisen.
– Service Mode aufrufen: Taste "
i
" drücken –> "
8500
" eingeben.
–
GRN
mit den Tasten
P+
/
P-
anwählen und mit den Tasten
Ǹ
/
Ƿ
auf
32
stellen.
–
RED
und
BLUE
jeweils mit den Tasten
P+
/
P-
anwählen und mit den
Tasten
Ǹ
/
Ƿ
so einstellen, dass der weiße Bildbereich
unbunt
ist.
Sollte sich der Weißwert nicht einstellen lassen, Wert für
GRN
korrigieren.
–
BLOR
und
BLOG
jeweils mit den Tasten
P+
/
P-
anwählen und mit
den Tasten
Ǹ
/
Ƿ
so einstellen, dass der dunkle Bildbereich
unbunt
ist.
– Service Mode beenden: Taste "
TXT
" drücken.
Summary of Contents for SEDANCE 70
