Thank you for purchasing our product. If there
are any questions, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or printing errors, and the
content is subject to change without notice.
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
Privacy Notice
Surveillance laws vary by jurisdiction. Check
all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specification for
camera parameters and functions.
GCT-K0126V
2 MEGAPIXEL FULL HD
VF FIXDOME HD-TVI
CAMERA LED, WDR
User Manual
1 INTRODUCTION
1.1 Product Features
This camera adopts new generation sensor with
high sensitivity and advanced circuit board design
technology. It possesses the features of high
resolution, low distortion, and low noise, etc. It
is extremely suitable for supervisory system and
image processing system.
The main features are as follows:
• High performance CMOS sensor and
high resolution bring high-quality image;
• Low illumination;
• Support IR cut filter with auto switch;
• OSD menu, parameters are configurable;
• Support auto white balance, auto gain control,
electronic shutter control and internal
synchronization;
• SMART IR mode;
• Unit transmission control;
• Advanced 3-axis design meets different
installation requirements.
1.2 Overview
Figure 1-1 Overview
2 INSTALLATION
Before you start:
• Please make sure that the device in the package is in
good condition and all the assembly parts are included.
• Make sure that all the related equipment is
power-off during the installation.
• Check the specification of the products for the
installation environment.
• Check whether the power supply is matched
with your power output to avoid damage.
• Please make sure the wall is strong enough to
withstand three times the weight of the
camera and the mounting.
• If the wall is the cement wall, you need to
insert expansion screws before you install the
camera. If the wall is the wooden wall, you can
use self-tapping screw to secure the camera.
• If the product does not function properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Ceiling
Steps:
1. Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2. Loosen the screws on the bubble to remove
the bubble and the black liner.
Figure 2-2 Remove the Bubble
3. Attach the back box to the ceiling and secure
them with supplied self-tapping screws.
4. Route the cables through the cable hole.
5. Align the camera with the back box/base
plate, and tighten the set screws to secure the
camera with the back box/base plate.
Figure 2-3 Fix the Camera to the Ceiling
6. Connect the corresponding cables.
7. Adjust the camera according to the figure
below to get an optimum angle.
8. Fit the black liner on the camera and tighten
the screws on the bubble to complete.
Figure 2-4 Zoom and Focus Adjustment
© ASP A
G (Grundig Security) 20160707
Regulatory Information
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked
with „CE“ and comply therefore with
the applicable harmonized European standards
listed under the Low Voltage Directive 2006/95/EC,
the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in the European Union.
For proper recycling, return this product to
your local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated collecti-
on points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot be disposed of as unsorted
municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg).
For proper recycling, return the battery to your supplier
or to a designated collection point. For more informati-
on see: www.recyclethis.inf
FCC Information
FCC compliance: This equipment has been tested
and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful inter-
ference in which case the user will be required to
correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
0~ 90
°°
0 ~35 5
°°
0~ 355
°°
P Direction
T Direction
R Direction
HD Video
Cabl e
Back Box
Len s
Bubbl e
Blac k Line r
Power Cable
12VDC (6W)
