Grundig 40 VLE 555 BG, Manual

Page: 49 / 60

­49
ENGLISH
speCiAl­settinGs
­----------------------------------------------------------------------------------------------------------
searching­for­digital­television­
channels­from­a­satellite­manu-
ally
If you know the parameters of a new television
channel, you can also search for it manually.
Current transponder data can be found in the
teletext, in satellite TV magazines or on the
Internet.
1
Open the menu with »
menu
«.
2 Select the menu item »SOURCE SETUP« with
»
v
« or »
Λ
« and press » oK « to confirm.
– The »SOURCE SETUP« menu appears.
3
Select the line »Digital Manual Tuning « with
»
v
« or »
Λ
« and press »
oK
« to confirm.
– The menu appears.
4 Select the line required for the parameters
with »
v
« or »
Λ
«.
– »Frequency (MHz)«: Enter the five-digit
frequency with » 1­...­0 « .
– »Symbol Rate (kS/s)«: Enter the five-digit
symbol rate with » 1­...­0 « .
– »Polarization«: Use »
<
« or »
>
« to set the
polarisation to »Horizontal« or »Vertical«.
– »Network Search«: use »
<
« or »
>
« to se-
lect the option »On« or »Off«.
– »Scan Mode«: Use »
<
« or »
>
« to select
whether you want to search for unencrypt-
ed (Unencrypted) channels only, encrypt-
ed (Encrypted) channels only, or for both
(Unenc Encrypted).
– »Service Type«: Use »
<
« or »
>
« to select
whether you want to search for television
channels only (TV), radio stations only
(Radio), or both (Radio + TV).
5 Start the scan with »

« (red).
– The »Results« menu appears, and the scan
for TV channels begins.
note:
7
You can abort the search by pressing
» exit «.
6 Press » exit « to end the setting.
lnB­settings
notes:
7
The following description about the LNB
settings premise a substantial expertise
about the satellite systems. Ask your
specialist dealer.
7
Your TV supports SCR system (Satellite
Channel Router). If you are using SCR
satellite system, follow the steps described
in »LNB Type« section.
1
Open the menu with »
menu
«.
2 Select the menu item »SOURCE SETUP« with
»
v
« or »
Λ
« and press » oK « to confirm.
– The »SOURCE SETUP« menu appears.
3
Select the line »Antenna Settings« with »
v
«
or »
Λ
« and press »
oK
« to confirm.
– The »ANTENNA SETTINGS« menu ap-
pears.
4 Select the line required for the parameters
with »
v
« or »
Λ
«.
– »Satellite«: »Press oK «, select a satellite
with »
<
«, »
>
«, »
v
« or »
Λ
« and press
» oK « to confirm.
– »Transponder«: »Press oK «, select a tran-
sponder with »
<
«, »
>
«, »
v
« or »
Λ
« and
press » oK « to confirm. Use »

« (red) to
add a transponder, use »

« (green) to
delete it, or use »

« (yellow) to change
transponder data.
– »LNB Power«: Set the LNB power supply
(depending on the type of LNB) to »Off«
»13/18 V« or »14/19 V« with »
<
« or »
>
«.
– »LNB Type«: Select the LNB type used
in the satellite system with »
<
« or »
>
«. If
you are using a satellite antenna with an
Single Cable Distribution multiswitch, select
the setting »Grundig SCR«. After it, please
perform the »User Band«, »KB Frequency«
and »LNB Selection« settings in the
submenus. The necessary parameters you
will get from the operator of the satellite
antenna. Use only this specification!
– »LNB Selection«: If more than one
satellites are used in the current SCR
system, select »1/2« to»2/2« for the
satellite corresponding to the relevant
positions using »
<
« or »
>
« buttons.