Grundig 32 VLE 5323 BG, Connecting And Operating Instructions

Page: 51 / 60

­51
ENGLISH
SpECIAL­SEttINGS
­----------------------------------------------------------------------------------------------------------
DiSEqC­1.2­Settings
You can adjust the alignment of the satellite an-
tenna to each individual satellite. These settings
will be saved so that the antenna can later be
easily guided to each saved alignment.
1 Select the line »DiSEqC 1.2 SETTINGS« with
»
v
« or »
Λ
« and press » oK « to confirm.
– The »DiSEqC 1.2 SETTINGS« menu ap-
pears.
2 Select the preferred option with »
v
«
or »
Λ
«.
– »Transponder«: »Press
oK
«, select the
transponder from which the signal is being
received with »
<
«, »
>
«, »
v
« or »
Λ
« and
press »
oK
« to confirm.
– »Moving Mode«: Use »
<
« or »
>
« to select
the option »Discrete« or »Continuous«.
– »Discrete«: Moves the antenna in
defined steps to the west and the east.
– »Continuous«: Moves the antenna to the
west or east continuously.
– »Step Size«: Use »
<
« or »
>
« to select the
number of steps with which the antenna
should turn. »Step Size« is only active
when the »Transport Mode« was set to
»Discrete«.
– »Move Motor«: Aligns the antenna with
the selected satellite. Use »
<
« to align it to
»West«, use »
>
« to align it to »East«.
– »Go To Stored Position«: Aligns the antenna
to a saved satellite position. Up to 50 posi-
tions can be saved. »Press oK « and then
select the saved position with »
<
« or »
>
«.
Press »

« (green) to confirm – the anten-
na will be aligned with the saved position.
– »Store Stored Position«: The current anten-
na alignment is saved.
– »Limit Position«: Defines the range in
which the antenna may move. Use »
<
«
to set the western limit, use »
>
« to set the
eastern limit.
– »Reset DiSEqC 1.2 Limit«: Resets the limit
position of the antenna.
3
Press »
mENu
« to end the setting.
Searching­for­television­chan-
nels­from­the­cable­provider­
automatically
1
Open the menu with »
mENu
«.
2 Select the menu item »SOURCE SETUP« with
»
v
« or »
Λ
« and press » oK « to confirm.
– The »SOURCE SETUP« menu appears.
3 Select the line »Source« with »
v
«
or »
Λ
« and press » oK « to confirm.
Select the option »Cable« with »
<
«, »
>
«,
»
v
« or »
Λ
« and press » oK « to confirm.
4 Select the line »Automatic Channel Search«
with »
v
« or »
Λ
« and press » oK « to confirm.
– The menu appears.
Scan Type
Exit
Back
SOURCE SETUP
AUTOMATIC CHANNEL
SEARCH
Country
Connection Type
Frequency (MHz)
Cable Scan Type
Network ID
U.K.
Cabel
Auto
Quick
Auto
08.08.2012
15:46
Start Search
DTV & ATV
5 Select the line »Scan Typ« with »
v
« or »
Λ
«
and set the option »DTV« with »
<
« or »
>
«.
6 Select the line »Cable Scan Type« with »
v
«
or »
Λ
« and set the option »Quick« or »Full«
with »
<
« or »
>
«.
– The search function »Quick« sets the channels
according to the information provided by your
cable provide in the transmission signal.
– If the option »Full« is selected, the entire fre-
quency range will be scanned. The search
can take a long time with this option. This
option is recommended if your cable pro-
vider does not support the search type
»Quick«.