Grundfos TPE 2 Series Installation And Operating Instructions Manual Download Page 64

Page: 64 / 70

English (GB)

31. Factory settings

Only available if you have fitted an advanced functional module, FM 300.

●

Function is enabled.

❍

Function is disabled.

Function is not available.

Settings

TPE3, TPE3 D

TPE2, TPE2 D

Function

description on

page

Setpoint

Auto

●

Operating mode

Normal

Control mode

AUTO

ADAPT

Const. curve

Date and time

●

FLOWLIMIT

❍

Automatic Night Setback

❍

Temperature influence

❍

Buttons on product

●

Controller (Controller settings)

1.0

0.5

8.0

0.5

Operating range

Min.

25 %

Max.

100 %

Ramps

❍

Ramp-up

1 second

Ramp-down

3 seconds

Number (Pump number)

Radio communication

●

Analog input 1

❍

Analog input 2

❍

Analog input 3

❍

Built-in Grundfos sensor

●

Grundfos differential pressure sensor

Feedback sensor

Grundfos temperature sensor

❍

Pt100/1000 input 1

❍

Pt100/1000 input 2

❍

Digital input 1

❍

Digital input 2

❍

Digital in/output 3

❍

Digital in/output 4

❍

Pulse flowmeter

❍

Predefined setpoints

❍

Analog output

❍

External setpoint function

❍

Signal relay 1

❍

Signal relay 2

❍

Limit 1 exceeded

❍

Limit 2 exceeded

❍

Standstill heating

❍

Motor bearing monitoring

❍

Pump name

Grundfos

Connection code

Unit configuration

Summary of Contents for TPE 2 Series







































































Search results

Summary of Contents for TPE 2 Series

Reviews:

Related manuals for TPE 2 Series

Brands by name

Popular brands

Grundfos TPE 2 Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for TPE 2 Series

Reviews:

Related manuals for TPE 2 Series

Brands by name

Popular brands