background image

English (GB)

3

2. Returning the product for service

If you request Grundfos to service the product, contact Grundfos 
with details about the pumped liquid before returning the product. 
Otherwise Grundfos can refuse to accept the pump for service.
Costs of returning the product are to be paid by the customer.
However, any application for service, no matter to whom it may 
be made, must include details about the pumped liquid if the 
product has been used for liquids which are injurious to health or 
toxic.

2.1 Servicing pumps with explosion-proof motors

Service work on Ex pumps must be carried out by Grundfos or a 
workshop authorised by Grundfos. Violation of this requirement 
will invalidate the Ex classification of the pump.
Overhauled and repaired explosion-proof pumps are provided 
with a repair plate giving this information:
• repair symbol R
• name of registered trade mark of the repairing workshop
• workshop reference number relating to the repair
• date of overhaul or repair.
In case of subsequent repairs, the existing repair plate should be 
replaced by a new, updated repair plated and earlier markings 
must be covered.
The repairing workshop must keep records of performed 
overhauls and repairs together with records of all previous 
overhauls, repairs and possible modifications. Copies of the 
repairing workshop’s detailed records should be filed by the 
owner or operator together with the original type certificate of the 
explosion-proof motor in question.

3. Safety

For safety reasons, all work in pits must be supervised by a 
person outside the pump pit.
Pits for submersible wastewater pumps contain wastewater with 
toxic and/or disease-causing substances. Therefore, all persons 
involved must wear appropriate personal protective equipment 
and clothing and all work on and near the pump must be carried 
out under strict observance of the hygiene regulations in force.

WARNING

Installation fault

Death or serious personal injury
- Pump installation in pits must be carried out by 

specially trained persons.

- Work in or near wastewater pits must be carried 

out according to local regulations.

CAUTION

Electric shock

Minor or moderate personal injury
- It must be possible to lock the mains switch in 

position 0.

- Type and requirements as specified in EN 60204-

1, 5.3.2.

We recommend that you make all maintenance and 
service work when the pump is placed outside the 
pit.

Before attempting to lift the pump, make sure that the 
lifting bracket is tightened. Tighten if necessary.

Summary of Contents for seg autoadapt



























Reviews: