background image

13

English (US)

The second test is completed.

Write down the pressure and/or flow rate, and state which test 
gave the highest pump performance:

First test

Second test

Make new test.

The correct direction of rotation has now been set.

Press OK to set the setpoint 

(8/11). 

See 

11.3.6 Setpoint

.

11.4 Menu GENERAL

The menu makes it possible to return to the start-up guide, which 
is usually only used during the first start-up of the CU331SP.

11.4.1 Return to start-up guide (0.1)

State your choice:

Yes

No.

If Yes is selected, all settings will be erased, and the entire 
start-up guide must be completed.

11.4.2 Type code change (0.2)

This display is for service use only.

11.5 Menu OPERATION

11.5.1 Setpoint (1.1)

Setpoint set

Actual setpoint

Actual value

Set the setpoint in units of the feedback sensor.

11.5.2 Operating mode (1.2)

Set one of the following operating modes: 

Normal

Max

Min 

Stop

The operating modes can be set without changing the setpoint 
setting. 

11.5.3 Fault indications

Faults may result in two types of indication: Alarm or warning. 

An 

"alarm"

 will activate an alarm indication in CU331SP and 

cause the pump to change operating mode, typically to stop. 
However, for some faults resulting in alarm, the pump is set to 
continue operating even if there is an alarm.

"warning"

 will activate a warning indication in CU331SP, but 

the pump will not change operating or control mode.

Alarm (1.3)

In case of an alarm, the cause will appear in the display. See 

14.1 Warning and alarm list

.

Warning (1.4)

In case of warning, the cause will appear in the display. See 
section 

14.1 Warning and alarm list

.

11.5.4 Fault log

For both fault types, alarm and warning, the CU331SP has a log 
function.

Alarm log (1.5-1.9)

In case of an "alarm", the last five alarm indications will appear in 
the alarm log. "Alarm log 1" shows the latest alarm, "Alarm log 2" 
shows the latest alarm but one, etc. 

The display shows three pieces of information: 

the alarm indication

the alarm code

the number of minutes the pump has been connected to the 
power supply after the alarm occurred. 

Note

Note

If the start-up guide is started, all previous 
settings will be erased!

Note

Note

The start-up guide must be carried out on a cold 
motor! 

Repeating the start-up guide may lead to a 
heating of the motor.

Summary of Contents for CU331SP

























Reviews: