background image

English (GB)

11

6. CIM 260 Modbus 3G/4G Cellular setup

Fig. 9

CIM 260 cellular module (top-side view)

 

* Only use this antenna connection if required by the telecom 

company.

6.1 Installation

 

6.1.1 Fitting a cellular antenna

Connect an antenna to CIM 260 to establish connection to the 
cellular network.

 

External antenna

See fig. 

10

.

Connect the antenna cable to the SMA connection (pos. 1) of CIM 
260. Install the antenna outside the control cabinet in a position 
with good reception conditions. If required by the telecom 
company, connect an additional antenna.

Fig. 10

Fitting an external cellular antenna

*  Only use this antenna connection if required by the telecom 

company.

6.1.2 Inserting the SIM card

Before inserting the SIM card into CIM 260, remove the PIN code, 
or set the PIN code to "4321".

Procedure

1. Insert the SIM card into a mobile phone.
2. Remove the PIN code from the SIM card, or set the PIN code 

to "4321". See the manual of the mobile phone.

3. Insert the SIM card into CIM 260. See fig. 

11

.

 

Fig. 11

Inserting the SIM card

TM

07

 16

61

 20

18

Pos.

Designation

Description

1

Battery socket

2

SIM card holder

3

Secondary SMA connection for cellular 
antenna*.

4

Primary SMA connection for cellular 
antenna.
This antenna must always be 
connected.

5

LED1

Yellow and green status LED for 
cellular communication

6

LED2

Red and green status LED for internal 
communication between CIM 260 and 
the CIU 262 unit.

7

SW1

To reset to factory settings, press and 
hold for at least 5 seconds.

CAUTION

Electric shock

Minor or moderate personal injury
- Before installation, make sure that the power 

supply has been switched off and that it cannot be 
accidentally switched on.

If CIU 262 is installed in a metal control cabinet, we 
recommend fitting an external antenna.
Grundfos offers different kinds of antennas. No 
antenna is supplied with CIU 262. You can order it 
separately.

1

2

3

4

5

6

7

T

M

07

 16

62

 24

1

8

Pos.

Description

1

Primary SMA connection for the cellular antenna.
This antenna must always be connected

2

Secondary SMA connection for the cellular antenna *.

The slanted edge of the SIM card must point 
downwards away from the connector.
The connectors on the SIM card must face inwards 
towards CIM 260. See fig. 

11

.

TM

07

 16

63

 20

18

Pos.

Description

1

SIM card holder

2

SIM card

1

2

1

2

Summary of Contents for CIU 202





























































Reviews: