GrowSpan PB01720R4 Manual Download | Manualshive

Page: 23 / 31

background image

GROWSPAN

™

ROUND PREMIUM HIGH TUNNELS

23

Revision date: 11.22.21

SHELTER CARE AND MAINTENANCE

Proper care and maintenance of the shelter is important.

Check the following items periodically to properly maintain

the shelter:
• Regularly check the main cover and panels (if

equipped) to see that these remain tight and in proper

repair.

• Check connections and all fasteners to verify that they

remain tight.

• Do not climb or stand on the frame or cover at anytime.
• Remove debris and objects that may accumulate on

the cover. Use tools that will not damage the cover

when removing debris.

• Remove snow to prevent excess accumulation. Use

tools that will not damage the cover when removing

snow.

• Check the contents of the high tunnel to verify that

nothing is touching the cover or the side panels that

could cause damage.

• Check the anchoring system to ensure that all

components are tight and in good repair.

• If the shelter is moved, inspect all parts and

connections before reassembling.

• For replacement or missing parts, call 1-800-245-9881

for assistance.

Space below is reserved for customer notes.

«
...
21
22
23
24
25
...
»

Summary of Contents for PB01720R4
































Reviews:

No comments

Related manuals for PB01720R4

Brand: Palram Pages: 98

Brand: Palram Applications Pages: 88

Brand: Palram Pages: 61

LED SUPERFLOWER

Brand: SuperCloset Pages: 12

3-in-1 Garden System

Brand: simpo Pages: 2

Brand: Vitavia Pages: 40

Brand: Vitavia Pages: 86

VM0011-MN+ 11500

Brand: Vitavia Pages: 36

Brand: Vitavia Pages: 24

Brand: Vitavia Pages: 32

Brand: Holman Pages: 5

Brand: General Hydroponics Pages: 12

Brand: FirstBuild Pages: 2

Mini Polytunnel

Brand: FIRST TUNNELS Pages: 12

Brand: Velcom Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands