background image

                                              

 WARRANTY

 

 
 
 
Examination of the goods has been made by or on behalf of the purchaser and no warranty condition, de-
scription or representation on the part of the manufacturer is given or is to be implied or has been given 
from anything said or written in the negotiations between the parties or their representative beyond those 
mentioned below.  Any statutory or other warrant condition, description or representation expressed or im-
plied as to the goods is hereby expressly excluded. 
 
In lieu, thereof the manufacturer undertakes to make good by repair or replacement at its option free of all 
charge during normal working hours.  Any defects in the goods arising in the manufacturer’s opinion from 
faulty design, materials or workmanship which shall become apparent within a period of 24 months in the 
case of machines, and 12 months in the case of spares from the date of receipt of the goods.   At the termi-
nation of which period, all liability on the manufacturer’s part ceases.  Provided always and the above war-
ranty is subject to the following conditions:  
 
A.  The manufacturer’s liability extents only to the repair or replacement and it accepts no liability for any 

consequential  or  other  loss,  damage  or  injury  resulting  directly  or  indirectly  from  any  defect  in  the 
goods. 

B.  The manufacturers warranty does not extent to failures, defects or damage attributable to wear and tear, 

improper adjustments, neglect, and alteration of specification or accident. 

C.  All defective parts must be returned to the dealer immediately together with full particulars of the de-

fects, the machine number, the hours worked and the date machine was supplied. 

D.  The manufacturers warranty does not extend to proprietary or other components not of its manufacture, 

but it will as far as possible pass to the purchaser any benefits of any guarantee given to the manufac-
turer in respect of such components. 

E.  In  the  event  of  the  rejection  by  the  manufacturer  of  any  claim,  the  part  or  parts returned  will  be  de-

stroyed unless specific instructions to the contrary were given when part or parts were returned. 

F.  No claim will be considered if other than genuine parts manufactured by the manufacturer or its order 

and listed in its catalogue are used. 

G.  This  warranty  should  only  be  construed  as  strictly  limited  in  its  application  and  is  valid  only  in  the 

country of purchase.  If the goods shall change hands during the period of this warranty, this warranty 
will cease to have effect. 

H.  The manufacturer accepts no responsibility for damage by fire or accident of any kind to any goods re-

turned under the terms of this warranty.  The manufacturer does not accept responsibility for any acci-
dent occurring to such goods whilst on the premises. 

I.  This warranty shall cease to have effect if the purchaser removes, defaces or alters the manufacturer’s 

number plate (serial number) or any other numbers or marks affixed to any Groundsman Industries Ltd 
product. 

J.  In respect to machines sold which have been used since the date of manufacture for commercial, con-

tract,  hire,  rental  or  demonstrator  purposes,  the  warranty  on  this  product  is  limited  in  duration  to  12 
months from the date of purchase. 

Page 4 

Summary of Contents for TMC48

























Reviews: