background image

 

 

Trouble shooting guide 

 

 

 

 

 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 

Terms of warranty  

 

The limited warranty for this product is covered by Ground Zero´s local distribution partners and their 

terms and conditions. For further information contact your local retailer or distributor. 

 

  

 
 

 

 

Ground Zero GmbH 

Erlenweg 25, 85658 Egmating, Germany 

Tel. +49 (0)8095/873 830 

 Fax -8310 

www.ground-zero-audio.com  

 

 

Symptoms 

Check / Cause 

Action 

No audible sound 

Does the POW LED turn to green? 

Check protection fuse(s) of the amplifier 
Check remote wire connection (RCA input mode) 
Check +12 Volt power supply wire connection 
Check ground wire connection 

Did the PRO LED turned to red? 

Check for speaker short or amplifier overheating 

Device does not turn on 

Power supply of the amplifier? 

Check power wire or connections 

Remote wire powered? (RCA input mode) 

Check remote wire connection to the head unit 

No sound on one channel 

Speaker wiring undamaged? 

Check for short circuit or open connections 

Input signal on both RCA leads? 

Reverse left and right RCA inputs to check the 
audio input signal 

Device turns off at medium / 
high volume 

Load impedance of each speaker correct? 

Check if each speaker load impedance matches 
the technical specifications of the amplifier 

Status LED turned on red 

Temperature protection circuit active 

Decrease head units volume / wait for cooling 

Speaker wires short / speaker damaged 

Check speaker / wires and insulate if necessary 

Summary of Contents for IRIDIUM SERIES









Reviews: