Grizzly T32057 Assembly Instructions Manual Download Page 4

Figure 7. Cutterhead insert at top-dead-center.

Straightedge 

Outfeed 

Infeed 

-4-

T32057 8" Helical Cutterhead Assembly

7.  Place  a  straightedge  on  outfeed  table 

so  it  extends  over  cutterhead,  and  rotate 
cutterhead  pulley  until  one  of  the  carbide 
inserts is at top-dead-center (TDC), as shown 
in 

Figure 7.

8.  Lock outfeed table, then re-install fence.

9.  Re-install V-belt on pulleys. (Refer to instruc-

tions in your G0855 manual for details.)

10.  Re-install rabbeting table, rear access panel, 

and belt cover.

11.  Install cutterhead guard back over cutterhead, 

making  sure  that  spring  tension  in  guard 
is  properly  set  so  guard  springs  back  over 
cutterhead  when  it  is  pulled  back  and 
released.

 

When  correctly  set,  carbide  insert  will  just 
touch straightedge when insert is at its high-
est point of rotation (see 

Figure 7).

— If  your  outfeed  table  is  correctly  set,  no 

adjustments are necessary.

— If  insert  lifts  straightedge  off  table  or  if 

table is below straightedge, adjust outfeed 
table height with handwheel until straight-
edge  just  touches  an  insert  at  its  highest 
point of rotation.

Summary of Contents for T32057









Reviews: