2.5. Active break
•
stops motor immediately with piston in default position and sping loose
•
increases lifetime of piston, sping and many other parts
•
always finishes whole rotation of gear wheels
•
fully functional in all fire modes
2.6. Malfunction detection
•
detects mechanical damage and blocks trigger from causing any more damage
•
warns user by vibrating (see
2.7. Li-Pol/Li-Ion/Li-Fe battery check
•
when lithium battery is discharged, warns user by vibrating (see
•
setting battery type by trigger
•
can be switched off for Ni
2.8. Realistic trigger operation
•
trigger sensitivity can be set during installation to best fit your demands (see
2.9. Anti-reversal latch
•
not needed if your motor is powerful enough (it is recommended to keep it)
•
solves problem with double shot on semi
2.10. Everything is set inside your gearbox
•
whole unit is inside your gearbox, replacing trigger contacts
•
only two power wires comes from gearbox
•
for easier installation, unit equipped with indication of correct installation
3. Technical parameters
•
Only high quality silicone wiring is used. 1mm2 in cut and ampacity up to 42A constant.
•
MOSFET with maximum current up to 202A constant and 808A in peek allows use without
any restrictions.
•
MOSFET is efectively cooled by whole gearbox.
•
Whole unit is covered in varnish for m
•
Current consumption of unit is 30mA tops.
•
Dimensions only 22x21x11mm.
4. PSJ-
! PSJ-M3 gen.2 should be installed by specialists only !
Advanced knowledge of AEG replicas is crucial. Also
skills are needed. Never use soldering gun! Manufacturer takes no responsibility for
damaged caused by unprofessional installation!
stops motor immediately with piston in default position and sping loose
piston, sping and many other parts
always finishes whole rotation of gear wheels
fully functional in all fire modes
detects mechanical damage and blocks trigger from causing any more damage
warns user by vibrating (see figure 5.3.)
Fe battery check
when lithium battery is discharged, warns user by vibrating (see figure 5.2.
setting battery type by trigger
can be switched off for Ni-MH, Ni-Cd batteries
Realistic trigger operation
trigger sensitivity can be set during installation to best fit your demands (see
not needed if your motor is powerful enough (it is recommended to keep it)
solves problem with double shot on semi
t inside your gearbox
whole unit is inside your gearbox, replacing trigger contacts
only two power wires comes from gearbox
for easier installation, unit equipped with indication of correct installation
Technical parameters
silicone wiring is used. 1mm2 in cut and ampacity up to 42A constant.
MOSFET with maximum current up to 202A constant and 808A in peek allows use without
MOSFET is efectively cooled by whole gearbox.
Whole unit is covered in varnish for maximum lifetime even in challenging conditions.
Current consumption of unit is 30mA tops.
Dimensions only 22x21x11mm.
-M3 installation
gen.2 should be installed by specialists only !
Advanced knowledge of AEG replicas is crucial. Also basics in electronics and soldering
skills are needed. Never use soldering gun! Manufacturer takes no responsibility for
damaged caused by unprofessional installation!
stops motor immediately with piston in default position and sping loose
detects mechanical damage and blocks trigger from causing any more damage
figure 5.2.)
trigger sensitivity can be set during installation to best fit your demands (see figure 4.5.)
not needed if your motor is powerful enough (it is recommended to keep it)
for easier installation, unit equipped with indication of correct installation
silicone wiring is used. 1mm2 in cut and ampacity up to 42A constant.
MOSFET with maximum current up to 202A constant and 808A in peek allows use without
aximum lifetime even in challenging conditions.
gen.2 should be installed by specialists only !
basics in electronics and soldering
skills are needed. Never use soldering gun! Manufacturer takes no responsibility for
Summary of Contents for PSJ-M3 GEN2
Page 1: ......
