background image

H7947/H7948 16 Gauge Stapler

-9

-

Rotating Exhaust 

Cover 

The exhaust cover rotates as needed to 
direct the exhaust away from you.

To rotate the exhaust cover:

1.

  Use the 4mm hex wrench to loosen the 

exhaust  cover  cap  screw  as  shown  in 

Figure 5

.

Figure 5.

 Loosening the exhaust cap 

screw.

2. 

Rotate  the  exhaust  cover  by  hand  to 
aim  the  exhaust  port  in  the  desired 
direction.

3. 

Tighten the exhaust cover cap screw.

Using the Stapler 

Before you operate your stapler, place five 
to  six  drops  of  air  tool  oil  into  the  quick 
connect fitting where the stapler connects 
to the air supply.

To operate your stapler:

1.

  Connect  the  air  supply  to  the  quick 

connect fitting on your stapler.

2.

  To  test  for  proper  staple  penetration, 

hold  the  stapler  perpendicular  to  the 
surface of a piece of clean scrap wood 
that  is  thick  enough  for  the  length  of 
staples you have loaded. 

3.

   Depress  the  safety  nose  mechanism   

against your workpiece.

Read  the  manual  before  operation. 
Become  familiar  with  these  staplers, 
their  safety  instructions,  and  opera-
tion  before  beginning  any  work. 
Serious  personal  injury  may  result  if 
safety  or  operational  information  is 
not understood or followed. 

Summary of Contents for H7947

























Reviews: