<%+,*&%?d^ciZg$EaVcZg8dbWdBVX]^cZ
"'."
I]Z ejgedhZ d[ WZkZa Xjii^c\ ^h id Xji V heZX^[^X
Vc\aZ^cidi]ZZY\Zd[Vldg`e^ZXZhZZ
Figures
37 & 38
#
I]ZBdYZa<%+,*]VhegZhZi[ZcXZhidehVi)*ß
djilVgY VcY .%ß# >[ ndjg h^ijVi^dc gZfj^gZh V Y^["
[ZgZciVc\aZ!i]ZegZhZi[ZcXZhidehXVcWZZVh^an
VY_jhiZY[dgndjgcZZYh#
To bevel cut on the jointer:
1.
GZVYVcYjcYZghiVcY
SECTION 1: SAFETY
,
WZ\^cc^c\dc
Page 6
#
2.
BV`Z hjgZ ndjg hidX` ]Vh WZZc ^cheZXiZY
[dgYVc\ZgdjhXdcY^i^dchVhYZhXg^WZY^ci]Z
Stock Inspection & Requirements
^chigjX"
i^dch!WZ\^cc^c\dc
Page 24.
3.
HZii]ZXjii^c\YZei][dgndjgdeZgVi^dc#LZ
hj\\Zhi WZilZZc
&
¿
&+
VcY
&
¿
-
[dg WZkZa Xji"
i^c\! jh^c\ V bdgZ h]Vaadl YZei] [dg ]VgY
lddYheZX^Zhdg[dgl^YZhidX`#
4.
BV`ZhjgZndjg[ZcXZ^hhZiidi]ZVc\aZd[
ndjgYZh^gZYXji!VY_jhii]ZWaVYZ\jVgY
(
¿
-
id
&
¿
'
VlVn[gdbi]Zldg`e^ZXZhZZ
Figure
37
!i]Zci^\]iZci]ZWaVYZ\jVgYadX``cdW#
5.
>[ndjgldg`e^ZXZ^hXjeeZYlVgeZY!eaVXZ
^i hd i]Z XdcXVkZ h^YZ ^h [VXZ Ydlc dc i]Z
hjg[VXZd[i]Z^c[ZZYiVWaZ#
6.
HiVgii]Z_d^ciZg#
7.
L^i]Vejh]WadX`^cndjgaZVY^c\]VcY!egZhh
i]Z ldg`e^ZXZ V\V^chi i]Z iVWaZ VcY [ZcXZ
l^i] [^gb egZhhjgZ! VcY [ZZY i]Z ldg`e^ZXZ
dkZgi]ZXjiiZg]ZVY#
Note:
If your leading hand gets within 4"
of the cutterhead, lift it up and over the
cutterhead, and place the push block on
the portion of the workpiece that is on the
outfeed table. Now, focus your pressure on
the outfeed end of the workpiece while feed-
ing, and repeat the same action with your
trailing hand when it gets within 4" of the
cutterhead. To keep your hands safe, DO
NOT let them get closer than 4" from the
cutterhead when it is moving!
8.
GZeZVi
Step 7
jci^a i]Z Vc\aZY Xji ^h hVi^h"
[VXidgnidndjgcZZYh#
Figure 38.
>aajhigVi^dcd[WZkZaXjii^c\gZhjaih#
NOTICE
If you are not experienced with a jointer,
set the depth of cut to 0", and practice
feeding the workpiece across the tables as
described below. This procedure will better
prepare you for the actual operation.
Bevel Cutting
Figure 37.
7ZkZaXjii^c\deZgVi^dc#
(
¿
-
"
&
¿
'
