background image

-6-

Model G0556/G0557 (Mfg. since 10/04)

The  purpose  of  this  section  is  to  guide  you 
through  the  required  steps  to  get  your  machine 
out of its packaging and into operating condition.

SECTION 2: SET UP

Wear safety glasses dur-

ing the entire setup pro-

cess!

This equipment pres-

ents serious injury haz-

ards to untrained users. 

Read through this entire 

manual to become famil-

iar with the operating 

 

 

procedures before using 

this equipment!

1.  Remove  the  box  from  around  the  Model 

G0556/G0557 Pan and Box Brake.

 

2.  Clean  the  protective  coating  from  machine 

surfaces. Note—Use a mild solvent and soft 
rag. Thinners, gasoline, acetone ect. will 
damage painted surfaces.

3.  Place  a  light  coat  of  machine  oil  on  all 

machined surfaces to prevent rust.

1.  Before mounting the Model G0556/G0557 to 

a flat and level work surface, make sure the 
mounting surface is solid enough to hold the 
pan and box brake and the work material.

2.  Place the pan and box brake onto the work 

surface and make sure adequate work room 
has been given on all sides.

 

3.  Using a pen or pencil, transfer the hole loca-

tion to the mounting surface.

4.  Mount the pan and box brake to work surface 

using 

5

/

16

" bolts.

Mounting

About This Section

Clean-Up

Your  machine  was  carefully  packaged  for  safe 
transportation.  Remove  the  packaging  materials 
from  around  your  machine  and  inspect  it.  If  you 
discover any damage, please call us immediately 
at (570) 546-9663
 for advice. 

Save the containers and all packing materials for 
possible  inspection  by  the  carrier  or  its  agent. 
Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.

Unpacking

Summary of Contents for G0556

















Reviews: