"')"
<%***AM
B[\#H^cXZ%&$&'
I]Z YZ[aZXi^dc bZi]dY ^h bjX] bdgZ hjW_ZXi^kZ
i]Vc i]Z [ajiiZg bZi]dY# :VX] WaVYZ l^aa YZ[aZXi
Y^[[ZgZcian VcY ZkZgn jhZg l^aa YZiZgb^cZ l]Vi
bdYZgViZ egZhhjgZ bZVch# I]Z [daadl^c\ VgZ
\ZcZgVa \j^YZa^cZh [dg iZch^dc^c\ i]Z WaVYZ l^i]
i]^hbZi]dY#
To tension the bandsaw blade:
1.
9>H8DCC:8I76C9H6L;GDBEDL:G#
2.
BV`Z hjgZ i]Z WaVYZ ^h egdeZgan igVX`^c\ Vh
^chigjXiZY^ci]Z
Blade Tracking
hjWhZXi^dc
dc
Page 19
#
3.
GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4.
:c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
5.
Jh^c\bdYZgViZegZhhjgZ!ejh]i]ZXZciZgd[
i]ZWaVYZh^YZlVnh#
·>[i]ZWaVYZYZ[aZXihVeegdm^bViZan
&
¿
)
^i^h
egdeZganiZch^dcZY#EgdXZZYid
Step 7
#
·>[i]ZWaVYZYZ[aZXihaZhhi]Vc
&
¿
)
^i^hdkZg"
iZch^dcZY#Ijgci]ZWaVYZiZch^dc^c\`cdW
XdjciZgXadX`l^hZild[jaaijgchVcYgZeZVi
Step 6
#
·>[i]ZWaVYZYZ[aZXih
&
¿
)
dgbdgZ!i]ZWaVYZ
^hcdiegdeZganiZch^dcZY#6eeaniZch^dcid
i]ZWaVYZ^cXgZbZciVaanVcYgZeZVi
Step 6
jci^aegdeZganiZch^dcZY#
6.
GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings
VcY
Adjusting Blade Guide Bearings
dc
Pages
25– 26
#
When using different size blades, the blade
tensioning system may need to be reset for
correct operation. Refer to
Blade Tensioner
on
Page 52
for detailed instructions.
Note:
Tensioning the blade according to the
blade tension scale before the
Test Run
was an
approximate tension. The following procedures
fine-tunes the blade tension.
1.
9>H8DCC:8I76C9H6L;GDBEDL:G#
2.
BV`ZhjgZi]ZWaVYZ^hegdeZganXZciZgigVX`"
^c\Vh^chigjXiZY^ci]Z
Blade Tracking
hjW"
hZXi^dcegZk^djhdc
Page 19
#
3.
GV^hZ i]Z \j^YZ edhi Vaa i]Z lVn VcY bdkZ
i]Z jeeZg VcY adlZg \j^YZ WZVg^c\h VlVn
[gdbi]ZWaVYZ#
4.
:c\V\Zi]ZWaVYZiZch^dcfj^X`gZaZVhZaZkZg
idVeeaniZch^dcidi]ZWaVYZ#
10.
GZ"VY_jhi WaVYZ \j^YZh Vh YZhXg^WZY ^c
Adjusting Blade Support Bearings
VcY
Adjusting Blade Guide Bearings
dc
Pages 25– 26
#
9.
9^hXdccZXii]ZWVcYhVl[gdbedlZg#
5.
8dccZXii]ZWVcYhVlidedlZg!VcYijgci]Z
WVcYhVl
ON
#
6 .
Jh^c\ i]Z WaVYZ iZch^dc VY_jhibZci `cdW!
hadlan YZXgZVhZ WaVYZ iZch^dc jci^a ndj hZZ
i]ZWaVYZhiVgiid[ajiiZg#
7
# Hadlan ^cXgZVhZ i]Z iZch^dc jci^a i]Z WaVYZ
hideh[ajiiZg^c\!i]Zci^\]iZci]ZWaVYZiZch^dc
VY_jhibZci `cdW VcY VYY^i^dcVa
&
¿
-
id
&
¿
)
d[ V
ijgc#
8.
Add` Vi l]Vi i]Z iZch^dc \Vj\Z gZVYh VcY
jhZi]ViVhV\j^YZ[dgiZch^dc^c\i]ViheZX^[^X
WaVYZ^ci]Z[jijgZ#
Note:
Do not rely on this setting for other
blades or for long periods of time because all
blades require specific tensioning and stretch
with use. If you notice a decrease in perfor-
mance at the setting repeat this procedure.
With extended use, the blade tensioning sys-
tem may need to be reset. Refer to
Resetting
Blade Tensioner
in the
Service
section in
this manual for details.
The Flutter Method
The Deflection Method
Summary of Contents for g0555lanv insert
Page 69: ...AM B H cXZ Main SECTION 9 PARTS...
Page 72: ...AM B H cXZ Table Fence Stand...