manualshive.com logo in svg

Grindex MAJOR, Installation, Care And Maintenance

Share
Download
Grindex MAJOR Installation, Care And Maintenance Download Page 4

Installation, care and maintenance 

Minor , Major

4

Product description

Applications

Minor

 and 

Major

 are intended to be used for:

— pumping of water which may contain abrasive 

particles.

The pumps are available in the following ver­

sions:

N

= Normal head version

H

= High head version

Liquid temperature: standard version, max. 

40°C (104°F).

Liquid density: max. 1100 kg/m

3

 (9.2 lb per US 

gal.).

The pumped liquid may contain particles up to 

a size which corresponds to the openings in the 

strainer. See drawing.

The pH of the pumped liquid: 5 – 8.

Depth of immersion: max. 20 m (65 ft).

For other applications contact your nearest 

Grindex representative for information.

WARNING!

The pump may not be used 

in an explosive or flammable 

environment or for pumping 

flammable liquids.

WARNING!

If the pump run dry or snore, 
the pump surface and the sur-

rounding liquid may be hot. 

Bear in mind the risk of burn 
injuries.

WARNING!

The machine is not to be 

installed in locations classified 

as hazardous in accordance 
with the national electric code, 
ANSI/NFPA 70-1990

Summary of Contents for MAJOR

























Reviews:

No comments

Brands by name

Popular brands

Load more brands