Grifco GSB-600 Instruction Manual Download | Manualshive

Page: 14 / 24

background image

14

INSTALLATION

STEP 8

MOUNT OPERATOR TO WALL BRACKET

The operator is approx. 30Kg so care should be

taken when handling.

Lifting Options:

1. The Operator may be lifted with a soft sling

around the motor/gearbox interface

2. Use an Eye-Bolt and nut (not supplied)

through one of the gearbox mounting holes

(caution - certain positions may cause

unbalanced load)

Fit the gear box bracket using M16 fasteners

supplied (Torque 190Nm—210Nm)

STEP 9

INSTALL SPROCKET

1. Install 10mmx8mmx80mm Key and 25T

sprocket.

2. Grease is recommended between sprocket

and shaft.

3. Install keeper plate and M10x25 Bolt with

spring washer (Torque 15Nm—17Nm).

«
...
12
13
14
15
16
...
»

Summary of Contents for GSB-600

























Reviews:

No comments

Related manuals for GSB-600

Brand: B&D Pages: 24

Brand: Chamberlain Pages: 45

Brand: Chamberlain Pages: 44

Brand: JOYTECH Pages: 26

Brand: CAME Pages: 28

Brand: FAAC Pages: 44

Brand: FAAC Pages: 36

Brand: V2 Pages: 22

Brand: Timotion Pages: 8

Brand: Cardin Elettronica Pages: 56

Brand: fadini Pages: 13

Brand: Avidsen Pages: 8

TOP EVO TOP 291E

Brand: GBD Pages: 24

Brand: Garage Door Centre Pages: 52

Brand: Nice Pages: 44

Brand: RIB Pages: 48

Brand: Rival Pages: 4

Brand: FAAC Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands