background image

Page 12

For technical questions, please call 1-800-444-3353.

SKU 96156 

        

spark Plug Maintenance

Disconnect spark plug wire from end 

1. 

of plug.  Clean out debris from around 
spark plug.

Using a spark plug wrench, remove the 

2. 

spark plug.

Inspect the spark plug: 

3. 

If the electrode is oily, clean it using a 
clean, dry rag. 
If the electrode has deposits on it, polish 
it using emery paper. 
If the white insulator is cracked or 
chipped, the spark plug needs to be 
replaced.

When installing a new spark plug, adjust 

4. 

the plug’s gap to the specification on the 

Specification chart.  Do not pry against 

the electrode or the insulator, the spark 
plug can be damaged.

Install the new spark plug or the cleaned 

5. 

spark plug into the engine.  Gasket-style:  
Finger-tighten until the gasket contacts 
the cylinder head, then about 1/2-2/3 
turn more. 
Non-gasket-style: Finger-tighten until the 
plug contacts the head, then about 1/16 
turn more.

Apply a small amount of dielectric grease 

6. 

(not included) to the insulator of the 
spark plug and attach the wire securely 
to the spark plug.

cleaning, Maintenance, and 

Lubrication schedule

note:

  This maintenance schedule is 

intended solely as a general guide.  If 
performance decreases or if engine 
operates unusually, check systems 
immediately.  The maintenance needs 
of each engine will differ depending on 
factors such as duty cycle, temperature, 
air quality, fuel quality, and other factors.

note:

  These procedures are in addition to 

the regular checks and maintenance 
explained as part of the regular operation 
of the engine.

after Initial 20 operation Hour Period:

Change engine oil.

a. 

every 25 operation Hours thereafter:

Clean/replace air filter element.

a. 

Inspect/clean spark plug.

b. 

every 50 operation Hours:

Change engine oil.

a. 

every 100 operation Hours:

Replace spark plug.

a. 

Replace air filter element.

b. 

note:

  All maintenance procedures scheduled 

for 25, 50, and 100 operation hours 
should be performed at least yearly.

every 300 operation Hours:

Clean fuel tank and carburetor.

a. 

Clean carbon build-up from combustion 

b. 

chamber.

Summary of Contents for 96156




















Reviews: