Greyhound 94837 Assembly And Operating Instructions Manual Download Page 2 | Manualshive

Page: 2 / 12

Greyhound 94837 Assembly And Operating Instructions Manual Download Page 2

Page 2

SKU 94837

For technical questions, please call 1-800-444-3353

Specifications

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep your invoice with this
manual. Write the invoice number on the inside of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1.

Keep work area clean. Cluttered areas invite injuries.

2.

Observe work area conditions. Do not use machines or power tools in damp or wet
locations. Don’t expose to rain. Keep work area well lighted. Do not use electrically
powered tools in the presence of flammable gases or liquids.

3.

Keep children away. Children must never be allowed in the work area. Do not let
them handle machines, tools, or extension cords.

4.

Store idle equipment. When not in use, tools must be stored in a dry location to
inhibit rust. Always lock up tools and keep out of reach of children.

5.

Dress properly. Do not wear loose clothing or jewelry as they can be caught in
moving parts. Protective, electrically non-conductive clothes and non-skid footwear
are recommended when working. Wear restrictive hair covering to contain long hair.

REV 07a; 09h

Item

Description

Pump Output

4.3 GPM (16.56 liter per min.) @ 3,60 RPM

Pump Type

Two Stage

Hydraulic Capacity

8 Tons, single stage pump

Ram Travel

19-7/8 inches

Ram Diameter

1.78 inches

Cutting Wedge

Thickness: 13/16 incl; Thick cabon steel

Log Capacity

20” (long) x 8” (dia.)

Towing

For off-road use only (not DOT approved); Hitch size: 1-7/8 inches

Hydraulic Fluid Reservoir

1.5 gallons

Type of Hydraulic Fluid

10W AW Hydraulic Fluid or Dexron III automatic transmission fluid.

Change every 100 hours of use.

Wheel Size

Wheel: 15 inch diameter; Hub: 8-1/2 inches; Wheel base: 20 inches

Tire Pressure

60 PSI Maximum

Engine

Briggs & Stratton Model 9J902 gasoline engine

Oil: 18 oz. of SAE 30 detergent oil rated SF,

SG, SH or higher; Spark Plug gap: 0.030”

(0.76mm), Part #802592; Gas type: unleaded,

85 octane or higher

Overall Dimensions

68”(L) x 27-3/4”(W) x 31-3/4”(H)

Weight

250 lbs.

«
1
2
3
4
...
»

Summary of Contents for 94837













Reviews:

No comments