manualshive.com logo in svg

GreenWorks 2000102, Owner'S Manual

Share
Download
GreenWorks 2000102 Owner'S Manual Download Page 37

3

7

 PROBLEM 

POSSIBLE CAUSE 

SOLUTION

  Bar and chain            Check chain tension for               Tension chain. Refer to Chain Tension     
    running  hot  and                  overtightened  condition.                              earlier  in  this  manual.                                                                               
  smoking. 
                                    Chain oil tank empty.                    Check oil tank.

  Motor runs, but          Chain tension too tight.                 Retention chain. Refer to Chain Tension
 chain is not rotating.                                                         earlier in this manual. 
 
                                    Check guide bar and chain           Refer to Replacing the Bar and Chain                                                 
                                    assembly.                                      earlier in this manual. 
 
                                    Check guide bar and chain for      Inspect guide bar and chain for damage. 
                                    damage.

  Motor runs, chain      Dull chain.                                     Sharpen chain. 
  rotates but does not 
  cut.                            Chain on backwards.                    Reverse direction of chain.

TROUBLESHOOTING

Summary of Contents for 2000102











































Reviews:

No comments

Brands by name

Popular brands

Load more brands