SENSOR/TIMER ADJUSTMENTS
2
3
1
Note: Switch off the mains electricity
before adjusting controls.
1 Remove one piece Internal Grille using
screwdriver. Push in to free catch then
twist to remove grille.
2 The timer is pre-set but may be adjusted
by using a screwdriver and rotating
clockwise to increase time and anti-
clockwise to reduce time overrun.
The humidity sensor is pre-set but may
be adjusted by using a screwdriver and
rotating clockwise to increase the
sensitivity and anti-clockwise to reduce
the sensitivity.
3 After adjustments replace Internal Grille
by pushing home.
Installation Instructions for AXS100, AXS100SELV, AXSU & AXSK Axial Fans for Bathroom, Toilets, Utility Rooms and Kitchens
1
0
0
m
m
1
1
5
m
m
6mm
1
0
0
m
m
6mm
1
1
5
m
m
1
2
3
4
5
6
WIRING DETAILS
The electrical connections must be carried out
by a qualified electrician in accordance with
IEE or local regulations.
WARNING: Isolate electricity supply before
starting work.
●
The fans are double insulated and do not
require an earth connection.
●
The fans must be connected to a double
pole isolating switch having contact
separation of at least 3 mm.
●
When supplied from a 5 amp lighting
circuit no local fuse is required.
Specification:
230 V~50 Hz.
Consumption:
AXS100
16W
AXS100SVI 20W
AXS125 24W
AXSK/U/150 35W
Cable Sizes:
Fixed flat wiring
2 core 1mm
2
3 core 1/1.5mm
2
Flexible round wiring 2 core 0.75mm
2
3 core 0.75mm
2
AXS100 Fans
AXSK, AXS125 & AXSU
Before commencing wiring remove centre
safety cover over PCB using a pair of pliers.
Before replacing centre safety cover, after
wiring, make sure the pull cord link is
located correctly behind the PC board as
shown (inset diagram 5). Refit safety cover
on completion of wiring by pushing home.
Note: If cable is supplied with earth core
this can be cut to the same length and
‘parked’ as shown in diagram 6.
If fixed flat cable is used or flexible cable
which is secured with suitable wall fixings
the cable clamp is not required.
If flexible cable is used without suitable
fixings use cable clamp and screw supplied
loose with the fan.
For SELV fans only
Maximum cable length between fan and
controller:
Conductor Size
Maximum length
0.75mm
2
2.3m
1.00mm
2
3.0m
WIRING DIAGRAMS
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
Jan 2006
●
Remove one piece Internal Grille using
screwdriver. Push in to free catch then
twist to remove grille.
●
The fan may now be cleaned using
a brush or damp cloth. DO NOT
IMMERSE IN WATER.
●
After cleaning replace Internal Grille
by pushing home.
WARNING: Always isolate fan
from mains supply before cleaning.
Do not use solvents to clean this fan.
TO CLEAN OR SERVICE FAN
Greenwood Air Management Ltd
Brookside Industrial Estate, Rustington, West Sussex BN16 3LH.
Tel:
(01903) 771021
Fax:
(01903) 782398
Web:
www.greenwood.co.uk
Email:
Remove the electrical cover.
Make all connections to the connector blocks.
Note: Mains cable must be fixed back to the
wall using appropriate cable cleats.
Replace electrical cover
Note: Do not fit more than one fan to the
controller or connect with any other product.
This equipment must be sited away from
direct water spray and heat in excess of 40˚C
the controller must not be sited within reach
of a person using a bath or shower nor within
a shower cubicle/enclosure.
AXS100, AXS125, AXS150
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
AXS100SVIB
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
AXS100PC, AXSK & AXSUPC
AXS100T, AXS100TR, AXS100DT,
AXS100HT AXSKMA & AXSUT, AXS125TR,
AXS150HTR
Mains
230 V ~ 50 Hz
To Fan 12 V
SELV FANS ONLY
TO WIRE THE CONTROLLER
L
N
Fan
Terminals
L
N
Double pole
isolating switch
Fuse
L
N
Fan
Terminals
N
L
Double pole
isolating switch
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
L
N
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
Double pole
isolating switch
1
2
3
Fuse
Controller
Terminals
12V Fan
Terminals
N
SL
L
2
3
1
1
2
3
L
N
Fan
Terminals
Light Switch
Switch
Light
Light
Fuse
L1
N
L
Double pole
isolating switch
Remote/Light
Switch
L
N
Light Switch
Light (optional)
Fuse
Double pole
isolating switch
SELV Fans External wiring for operation in parallel with
room light or remote switch with or without pull cord
SVI 12 V Controller
(with switch line)
SELV Fans
External wiring for pull cord only
