background image

Page 5

For technical questions, please call 1-888-866-5797.

Item 63092 

        

Assembly Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document 

including all text under subheadings therein before set up or use of this product.

Assembling the Wand

1.  Insert end of Wand into end of 

Wand Handle Assembly.

2.  Slide Hose Nut (27) over threaded end of 

Handle, then tighten Hose Nut securely.

Wand 

Handle 

Assembly

Hose 

Nut

Wand

Figure B

Changing the Nozzle

1.  Loosen Hose Nut (27) and remove Single 

Nozzle (53) from end of Wand.

2.  Choose another Nozzle:

a.  Double Nozzle (54)
b.  Fan Nozzle (55)
c.  Sprinkler Nozzle (56)

3.  Slide Nozzle over end of Wand, slide Hose Nut over 

threads of Nozzle, then tighten Hose Nut securely.

Single 

Nozzle 

Hose 

Nut

Double 

Nozzle 

Fan 

Nozzle 

Sprinkler 

Nozzle 

Wand

 

Figure C

Pump Handle Orientation

To change the side that the Pump Handle is on:

1.  Pass the end of the Strap through the 

back of the Buckle, then around the bar 

until it is free.  

(See Figure D.)

2.  Route the Strap to the other side of the 

Tank, then reattach the Strap.

3.  Do this to both Straps.

Bar

Figure D

Summary of Contents for 4 GALLON HOME & GARDEN BACKPACK SPRAYER













Reviews: