Greenlee GATOR CK1230 Instruction Manual Download Page 3

Greenlee / A Textron Company

3

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

CK1230 and CK1230C Crimping Tools

IMPORTANT SAFETY INFORMATION

Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.

Failure to observe this warning will
result in severe injury or death.

• Do not expose to rain.

• Do not use in wet or damp

locations.

Failure to observe these warnings
could result in severe injury or death.

Electric shock hazard:

• Connect the power cord to a

receptacle of proper voltage for
the tool in use on a ground fault-
protected circuit only.

• Do not modify the power cord or

plug.

• Inspect the power cord before use.

Repair or replace the cord if
damaged.

• Do not pull or carry by cord, use

the cord as a handle, close a door
on the cord, run over the cord, or
pull the cord around sharp edges
or corners. Keep the cord away
from heated surfaces.

• Do not unplug by pulling on the

cord. To unplug, grasp and pull
the plug—not the cord.

• Disconnect from power before

servicing.

Failure to observe these warnings
could result in severe injury or death.

Do not use this crimping tool in a
hazardous environment. Hazards
include flammable liquids, gases, or
other materials. Using this crimping
tool in a hazardous environment can
result in a fire or explosion.

Failure to observe this warning will
result in severe injury or death.

This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, defined below,
indicates the severity of the hazard. The message
after the signal word provides information for
preventing or avoiding the hazard.

Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.

Hazards which, if not avoided, COULD result in
severe injury or death.

Immediate hazards which, if not avoided, WILL
result in severe injury or death.

SAFETY
ALERT
SYMBOL

Electric shock hazard:

This tool is not insulated. When
using this unit on or near energized
electrical lines, use proper personal
protective equipment.

Failure to observe this warning could
result in severe injury or death.

Summary of Contents for GATOR CK1230



















Reviews: