manualshive.com logo in svg

Greenlee 555-22, Instruction Manual, Page: 3 / 44

Share
Download
Greenlee 555-22 Instruction Manual Download Page 3

Greenlee / A Textron Company

3

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

555

®

-22 Electric Bender

This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, defined below,
indicates the severity of the hazard. The message
after the signal word provides information for
preventing or avoiding the hazard.

Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.

Hazards which, if not avoided, COULD result in
severe injury or death.

Immediate hazards which, if not avoided, WILL
result in severe injury or death.

SAFETY
ALERT
SYMBOL

Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.

Failure to observe this warning will
result in severe injury or death.

• Do not expose to rain.

• Do not use in wet or damp

locations.

Failure to observe these warnings
could result in severe injury or death.

Wear eye protection when operating
or servicing this tool.

Failure to wear eye protection could
result in serious eye injury from
flying debris.

Do not remove guards.

Failure to observe this warning could
result in severe injury or death.

Do not use this tool in a hazardous
environment. Hazards include
flammable liquids, gases, or other
materials. Using this tool in a haz-
ardous environment can result in a
fire or explosion.

Failure to observe this warning will
result in severe injury or death.

IMPORTANT SAFETY INFORMATION

Electric shock hazard:

• Connect the power cord to a 220

volt, 15 amp receptacle on a
ground fault protected circuit only.
See Grounding Instructions.

• Do not modify the power cord or

plug.

• Inspect the power cord before use.

Repair or replace the cord if
damaged.

• Disconnect from power before

servicing.

Failure to observe this warning could
result in severe injury or death.

Summary of Contents for 555-22













































Reviews:

No comments