background image

Model FSDGB-211

Steel 3V Blades

Qualified to Standard GB 15931-1995

Combination 

FIRE SMOKE DAMPERS

* W & H dimensions furnished approximately 6mm (1/4 in.) 

undersize.

  (Add sleeve thickness for overall sleeved damper dimension)
  Right hand drive is shown. Left hand drive is available upon request.

Application

Model FSDGB-211 is a combination fire smoke damper with 3V style 

blades. The FSDGB-211 has been qualified to Standard  

GB 15931-1995 for operation and  closure in emergency fire smoke 

situations. Model FSDGB-211 may be installed vertically (with 

blades running horizontal) or horizontally and is rated for airflow and 

leakage in either direction.

Ratings

 

 

Standard GB 15931-1995 

 

Velocity:

 

10 m/s (2000 fpm) 

 

Pressure:

 

1kPa (4 in. wg)

Standard Construction

 

Frame:

  

127mm x 25.4 mm (5 in. x 1 in.) 

 

 

1.24mm galvanized steel hat 

 

 

channel with reinforced corners. A 

 

 

low profile head and sill are used on 

 

 

sizes less than 432mm (17 in.) high 

 

 

to maximize free area and  

 

 

performance. 

 

 

Blades:

  

1.24mm (16 ga.) galvanized steel, 

 

 

reinforced with 3 longitudinal 

 

 

structurally designed vee’s.  

 

Seals:

 

Extruded silicone rubber blade 

 

 

seals. Flexible stainless steel jamb 

 

 

seals. 

 

Linkage:

 

Concealed in jamb. 

 

Axles:

 

12.7 mm (

1

2

 in.) dia. plated steel. 

 

Bearings:

 

Bronze sleeve type. 

 

Fusible Link:

  

280° C

Size Limitations

 

 

Minimum Size: 

204mm W x 152mm H 

 

 

(8 in. W x 6 in. H)

 

 

Maximum Size:

 

 

Single Section: 

813mm W x 914mm H  

 

 

(32 in. W x 36 in. H) 

 

Multiple Section: 

1626mm W x 914mm H 

 

 

(64 in. W x  36 in. H)

Optional Features

• Stainless steel bearings

• OCI (Open closed indication switches)

• Retaining Angles

• Transitions (C, O, R)

• Sealed transitions and sleeves

• Sleeve with integral flange on both sides

R

Greenheck Kunshan Co. Ltd. and Greenheck Fan 

Corporation certifies that the model FSDGB-211 

shown herein is licensed to bear the AMCA Seal. The 

ratings shown are based on tests and procedures 

performed in accordance with AMCA Publication 

511 and comply with the requirements of the AMCA 

Certified Ratings Programs. The AMCA Certified 
Ratings Seal applies to air performance ratings only. 

Summary of Contents for Fire Smoke Dampers FSDGB-211







Reviews: