USAGE
INSTALLATION INSTRUCTIONS
The hand-dryer is intended to be affixed to a vertical wall in industrial and commercial areas and to be
used exclusively for drying hands. The electrician should determine the suitability of area to fit.
Always ensure that the installation conforms to the current edition of the wiring regulations, BS
7671
(UK) or
the appropriate standards in your country.
Ensure that the unit is separately fused with a
5
A fuse, we recommend connecting to a RCD double pole spur
unit (similar to a PowerBreaker H
92
model
)
.
Care should be taken that single insulated conductors cannot come into contact with the mounting
surface.
SAFETY PRECAUTIONS
1
.
Read all the instructions carefully before using the appliance.
2
.
Remove the packages and ensure that the appliance is undamaged.
In case of doubt do not use the appliance and contact your supplier.
3
.
Do not install the automatic hand dryer on wooden or plastic walls.
4
.
Do not install the appliance within range of people using baths or showers.
5
.
Before installing the unit, check that the electrical voltage of your main supply corresponds to the voltage
marked on the rating label of the appliance.
6
.
Before installing the appliance, check that there are no obstructions within
50
cm of the sensor.
7
.
Before maintenance or repair, make sure that the unit is disconnected.
8
.
Do not insert any objects into the appliance.
9
.
Prevent water from getting into the housing of the appliance during operation or in storage.
Hazard of electric shock, always store in dry area with no moisture.
10
. Do not use outdoors.
11
. The appliance is not intended for use by young children or infirm persons without supervision.
Description of parts:-
1. Cover
2. Air Outlet
3. Infrared-sensor
4. Power Cable
3
4
2
1
1
.
Remove all packaging materials carefully.
2
.
Check for service pipes and cables in the wall before drilling.
3
.
Drill four holes with a diameter of 6mm where the unit is to be installed, according to the dimension
sketch as shown in Dia.
1,
and insert wall plugs.
4.
A distance of at least
200
mm to the next wall (or other solid objects) must be kept for servicing to both
sides.
5.
A
distance of at least
800
mm below the hand dryer must be kept clear from any radiators, wash basins
etc located below the unit.
6
.
Follow the suggested assembly heights. The assembly height is measured from the upper assembly
holes to the floor and is determined as following:-
a)
1.5
metres above floor for normal use.
b)
800
mm distance above shelves, sinks or radiators.
7
.
Unscrew both the screws on the front side of the hand dryer and detach the cover (
1
) by tilting it
upwards (Dia.
3).
AFTER INSTALLATION OR SERVICING, UNITS MUST BE CHECKED AND ONLY LEFT
WHEN ELECTRICALLY AND MECHANICALLY SAFE.
The hand dryer must not be installed within range of people using baths and/or showers.
Dia.
2
212
mm
1
5
7
m
m
Dia.
1
m
in
.
8
0
0
m
m
min.
200
mm
8.
Fix the hand dryer with the
4
enclosed screws to the
holes. It can be helpful to use flat washers for assembly,
to achieve a clean and secured assembly. Please keep in
mind that the assembly area must be even and clean.
9
.
Using the miniature slide switch on the front of the fan
housing, set the switch to ‘Cool’ (
500
W) or ‘Heat’
(
1000
W).
10
. Replace the cover by positioning the cover (
1
) at first
below the air outlet (
2
). Now place the cover over the
hand dryer and push or draw the upper edge of the cover
with both the retaining collars as far as the retaining
base, until the cover latches.
11
. The hand dryer should be connected to the mains supply
via a fused spur unit.
Dia.
3
