Sleep
Wake Up
Setup button
Stickers
x2
Do not remove
the cover plate
Wake Up/Sleep control
LE12496A
A
-EN
Wireless and batteryless Wake Up/Sleep control
0 648 84L/85L - 0 677 86L
0 770 57L - 6 000 84L
5 742 87/93 - 5 743 22 - 5 748 36
7 418 03L/33L/63L
Or
Requires to install the connected starter pack and one or more «... with Netatmo» connected switch, micromodule
or socket outlet
Module Control
Gateway power outlet and home/away wireless
master switch
Pack contents:
Frequency bands: 2.4 - 2.4835 GHz
Power level: < 100 mW
2
> 3 s
Or
Start the configuration
Press the configuration button of Module Control or press the middle of the wireless master switch (with battery)
until its light briefly turns green, and then stop pressing. All wired products lights will turn green.
3
A
+
+
A
2
B
C
C
A
1
B
A
1
B
C
A
2
To complete your installation,
-
ration of the
Module Control
or the middle of
the wire-
less Home / Away master switch.
Complete the installation
< 1 s
Or
< 1 s
+
batteryless control (factory reset)
While holding the "setup" button on the wireless batteryless
control, press the "Wake Up" button for 5 seconds.
Check that your control is correctly reset by making an
"Wake Up" command, then "Sleep"
5 s
Pair the wireless, batteryless switch to your connected installation.
Make sure that the indicator lights on the wired products are green and not flashing.
If not, go back to step
1
.
wired product flashes rapidly.
For the specific case of the latching relay, press the main button of the latching relay until the configuration indicator
flashes slowly in blue, release it then tap it 3 times with the wireless, batteryless "Wake Up/Sleep control". The indicator
light of the wired product flashes rapidly.
While holding the "setup" button on the wireless, batteryless control, briefly press the "Wake Up" or "Sleep" control on the
wireless batteryless control.
The indicator light of the wired product will briefly turn blue, and then will turn green again.The pairing was successful.
Complete the configuration of the scenarios using your HOME + CONTROL application, menu "Settings", then
"Scenarios"
4
H > 2 m
H < 2 m
Put the stickers in place
The undersigned, Legrand declares that the radio-electric equipment type
(0 648 84L/85L - 0 677 86L - 0 770 57L - 6 000 84L - 5 742 87/93 - 5 743 22 -
5 748 36 - 7 418 03L/33L/63L)
complies with directive 2014/53/EU. The full text of the EU declaration of
conformity is available on the following website:
www.legrandoc.com
LEGRAND - Pro and Consumer Service - BP 30076
87002 LIMOGES CEDEX FRANCE • www.legrand.com
www.legrandoc.com/064884L
Model: ZLGP16
FCC ID: 2ACN8-ZLGP1X
IC: 12132A-ZLGP1X
Model : ZLGP16
Before fixing the wireless control(s) with
the removable stickers provided, test one
on a non-visible area of the wall.
You can also fix the wireless control(s) permanently to the
wall with screws.
Download the app
Your installation is ready. You can download the Legrand Home +
Control application to control your lights remotely.
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) This device
must accept any interference, including interference that may cause undesired operation of the device.
-
ration distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Safety instructions
Make sure the power supply is disconnected before any intervention.
Strictly comply with instructions for installation and use.
